manualshive.com logo in svg

Gorilla Playsets 1500GW, Manual, Page: 76 / 150

Share
Download
Gorilla Playsets 1500GW Manual Download Page 76

HEX BOLT

5/16 X 3-1/2"

5/16 X 4-1/2"

LAG SCREW

DETAIL A 

2 X 6 X 70"

SANDBOX BOARD

5/16" WASHER

2 X 6 X 70"

SANDBOX BOARD

5/16" WASHER

5/16 X 4-1/2"

LAG SCREW

5/16" WASHER

HEX BOLT

5/16 X 3-1/2"

REAR OF FORT

2 X 4 X 70"

RAILING

A

STEP 24: ATTACHING SANDBOX BOARD & RAILING

1: PLACE THE 2 X 6 X 70" SANDBOX BOARD (OFFSET UP) AT THE BOTTOM OF THE REAR CORNER POSTS. 

FASTEN THE TOP HOLES IN THE SANDBOX BOARD TO THE REAR CORNER POSTS WITH 5/16" X 4-1/2" HEX 

BOLTS AND 5/16" WASHERS.

2: PLACE THE 2 X 4 X 70" UPPER LEVEL STEPS/RAILING BOARD (3 HOLES ON CENTER) AT THE TOP OF THE 

REAR CORNER POSTS. THIS BOARD WILL GET ATTACHED TO THE 2ND HOLE DOWN FROM THE TOP OF 

THE POSTS. THE T-NUT FOR THIS BOARD SHOULD BE ON THE INSIDE OF EACH POST ALREADY. FASTEN THE 

UPPER LEVEL RAILING BOARD TO THE REAR CORNER POSTS WITH 5/16" X 4-1/2" HEX BOLTS AND 5/16" 

WASHERS.

3: THE BOTTOM HOLES OF THE 2 X 6 X 70" SANDBOX BOARD SECURE AT THE BASE OF THE REAR CORNER 

POSTS, WITH 5/16 X 3-1/2" LAG SCREWS AND 5/16" WASHERS.

68

Summary of Contents for 1500GW























































































































































Reviews:

No comments