manualshive.com logo in svg

Gorilla Playsets 1500GW, Manual, Page: 62 / 150

Share
Download
Gorilla Playsets 1500GW Manual Download Page 62

 20 3

16 " 

 1 11

16 " 

2" WOOD SCREW

NOTE: BOTTOM PANEL BOARD REMOVED FOR CLARITY.

FRONT OF FORT

5/4 X 4 X 40-3/8"

DECK SPACER

2: PLACE THE 5/4 X 4 X 40-3/8" DECK SPACER AT ONE END OF THE FORT. CENTER THE BOARD BETWEEN THE

CORNER POSTS AND ATTACH IT WITH 2" WOOD SCREWS THROUGH THE PREDRILLED HOLES AND INTO THE DECK

SUPPORT BELOW. NOTE THE TOP OF THE SCREW HEAD SHOULD BE FLUSH TO THE TOP OF THE DECK SPACER.

  11

 1" 

16 " 

 2 38 " 

STEP 10: DECK SPACERS

THE FOLLOWING STEP IS RECOMMENDED TO PREVENT POSSIBLE SPLITS IN THE WOOD

1: PRE-DRILL THE ENDS OF THE 5/4 X 4 X 40-3/8" DECK SPACERS TO PREVENT INSTALLATION DAMAGE. PRE-DRILL

BOTH ENDS WITH A 1/8" DRILL BIT AT THE DIMENSIONS SHOWN BELOW. THE HOLE AT 20-3/16" IS THE CENTER OF THE

BOARD AND ONLY NEEDS TO BE DRILLED ONCE. THIS HOLE IS TO ATTACH THE CENTER DECK SUPPORT TO THE

DECK SPACER.

54

Summary of Contents for 1500GW























































































































































Reviews:

No comments