Gorilla Playsets 1500CTC Manual Download Page 114

Page: 114 / 138

SUPPORT TO THE RIGHT REAR CORNER POST.

INTO THE 2 X 6 X 21-1/2" END PANEL BOARD. USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE ANGLE

2: FOR THE ANGLE SUPPORT AT THE RIGHT REAR USE TWO 2-1/2" WOOD SCREWS THROUGH THE TOP OF THE BRACE

STEP 39: ANGLE SUPPORTS ON TUBE SLIDE SIDE

1: TWO 2 X 4 X 18" ANGLE SUPPORTS ARE MOUNTED UNDER THE DECK ON THE RIGHT SIDE (TUBE SLIDE SIDE).

3: FOR THE 2 X 4 X 18" ANGLE SUPPORTS AT THE RIGHT FRONT USE TWO2-1/2" WOOD SCREWS THROUGH THE DECK

AND INTO THE ANGLE SUPPORT. USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE

RIGHT FRONT ANGLE SUPPORTS TO THE RIGHT FRONT CORNER POST.

3" WOOD

SCREW

2" WOOD

SCREW

USE TWO 2-1/2"

WOOD SCREWS

TO FASTEN THIS

ANGLE SUPPORT

TO THE DECK

SPACER.

ANGLE SUPPORT

AT RIGHT REAR.

2 X 4 X 18"

USE TWO 2-1/2"

WOOD SCREWS

TO FASTEN THE

ANGLE SUPPORT

TO THE 2 X 6 X

21-1/2" END

PANEL BOARD.

2 X 4 X 18"

ANGLE

SUPPORT AT

RIGHT FRONT.

Summary of Contents for 1500CTC











































































































































Search results

Summary of Contents for 1500CTC

Reviews:

Related manuals for 1500CTC

Brands by name

Popular brands

Gorilla Playsets 1500CTC, Manual

Search results

Summary of Contents for 1500CTC

Reviews:

Related manuals for 1500CTC

Brands by name

Popular brands