background image

2 X 4 X 32-1/2"

PICNIC TABLE SLAT

TOP OF PIECES SHOULD BE FLUSH HERE

PT LEG

PT TOP SUPPORT

2 X 4 X 14-3/4"

PT SEAT SUPPORT

2 X 4 X 27-1/2"

#8 X 2-1/2"

WOOD SCREW

5/4 X 3 X 13-1/4"

#8 X 2" WOOD SCREW

2

 7 1

 10" 

16

  3 " 

 6 15

16 " 

PICNIC TABLE SLAT TO THE SUPPORTS WITH TWO #8 X 2" WOOD SCREWS.

LEFT SIDE ASSEMBLY

STEP 34: PICNIC TABLE

1: LOCATE TWO 2 X 4 X 14-3/4" PT TOP SUPPORTS, TWO 2 X 4 X 27-1/2" PT SEAT SUPPORTS, TWO 2 X 4 X 32-1/2" PT LEGS AND 

TWO 5/4 X 3 X 13-1/4" PICNIC TABLE SLATS.
2: FOR THE LEFT SIDE ASSEMBLY, PLACE A 2 X 4 X 14-3/4" PT TOP SUPPORT AND A 2 X 4 X 27-1/2" PT SEAT SUPPORT PARALLEL 

TO ONE ANOTHER.  PLACE A 2 X 4 X 32-1/2" PT LEG ON TOP AT THE 7-1/2" DIMENSION. THE TOP OF THE PT LEG SHOULD BE 

FLUSH TO THE TOP OF THE PT TOP SUPPORT.  ATTACH THE PT LEG TO THE SUPPORTS WITH #8 X 2-1/2" WOOD SCREWS.
3: FOR THE RIGHT SIDE ASSEMBLY, PLACE A 2 X 4 X 14-3/4" PT TOP SUPPORT AND A 2 X 4 X 27-1/2" PT SEAT SUPPORT 

PARALLEL TO ONE ANOTHER.  PLACE A 2 X 4 X 32-1/2" PT LEG ON TOP AT THE 7-1/2" DIMENSION. THE TOP OF THE PT LEG 

SHOULD BE FLUSH TO THE TOP OF THE PT TOP SUPPORT.  ATTACH THE PT LEG TO THE SUPPORTS WITH #8 X 2-1/2" WOOD 

SCREWS.
4: PLACE THE PICNIC TABLE SLAT NEXT TO THE PICNIC TABLE LEG FOR EACH ASSEMBLY BELOW. LEAVE A 3/16" GAP BETWEEN 

THE TOP OF THE SLAT AND THE LEG. USE THE 6-15/16" DIMENSION TO LOCATE THE BOTTOM END OF THE SLAT.  FASTEN THE 

RIGHT SIDE ASSEMBLY

2 X 4 X 32-1/2"

PICNIC TABLE SLAT

2 X 4 X 14-3/4"

PT TOP SUPPORT

PT LEG

TOP OF PIECES SHOULD BE FLUSH HERE

PT SEAT SUPPORT

2 X 4 X 27-1/2"

#8 X 2-1/2"

WOOD SCREW

5/4 X 3 X 13-1/4"

#8 X 2" WOOD SCREW

2

 7 1

 10" 

16

 6 15 " 

  3

16 " 

71

Summary of Contents for 1500CTC











































































































































Reviews: