- 20 -
electronic memory must be reset by pressing button
A
for
approximately
5 seconds
, until the indication
F
or
A
shown
on the display
C
stops flashing.
• COMMANDS: ELECTRONIC
(Fig.15A):
A
= LIGHT
B
= OFF/SPEED I
C
= SPEED II
D
= SPEED III
E
= AUTOMATIC STOP TIMER – 15 minutes
(*)
F
= FILTER SATURATION RESET LIGHT
When the “filter saturation” light flashes, the anti-grease
filters must be washed. When the light comes on without
flashing, the anti-grease filters must be washed and the
carbon filters replaced (in case of operation whit the recy-
cling version). When this operation has been completed,
press the key to reset it.
• COMMANDS:
(Fig.13)
LUMINOUS
(Fig.15B)
ELECTRONIC
the key symbols are explained
below:
A
= LIGHT
B
= OFF
C
= SPEED I
D
= SPEED II
E
= SPEED III
F
= AUTOMATIC STOP TIMER - 15 minutes
(*)
•
If your appliance does not have the
INTENSIVE
speed
function, press key E for two seconds and it will be activated
for 10 minutes after which it will return to the previously
set speed. When the function is active the LED flashes. To
interrupt it before the 10 minutes have expired press key
E
again.
•
By pressing key
F
for two seconds (with the hood switched
off) the “
clean air
” function is activated. This function
switches the appliance on for ten minutes every hour at
the first speed. As soon as this function is activated the
motor starts up at the first speed for ten minutes, During
this time key
F
and key
C
must flash at the same time.
After ten minutes the motor switches off and the LED of
key
F
remains switched on with a fixed light until the motor
starts up again at the first speed after fifty minutes and
keys
F
and
C
start to flash again for ten minutes and so
on.
By pressing any key for the exclusion of the hood light the
hood will return immediately to its normal functioning (e.g.
if key D is pressed the “
clean air
” function is deactivated
and the motor moves to the 2nd speed straight away. By
pressing key
B
the function is deactivated).
(*)
The
“automatic stop timer”
delays stopping of the
hood, which will continue functioning for 15 minutes at the
operating speed set at the time this function is activated.
• Active carbon/grease filter saturation:
- When button
A
flashes at a frequency of
2 seconds
, the
grease
filters must be cleaned.
- When button
A
flashes at a frequency of
0.5 seconds
,
the
carbon
filters must be replaced.
After the clean filter has been replaced, the electronic
memor y must be reset by pressing button
A
for
approximately
5 seconds
, until the light on the button stops
flashing.
•COMMANDS:
(Fig.11-12A)MECHANICAL_(Fig.12B)
Elliptic the key symbols are explained below:
A
= LIGHT
B
= OFF
C
= SPEED I
D
= SPEED II
E
= SPEED III
G
= MOTOR WORKING indicator
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY FOR EVENTUAL DAMAGES CAUSED
BY BREACHING THE ABOVE WARNINGS.
Summary of Contents for DTG6330E
