Google Pixel 6 Pro Service Manual Download Page 49

Page: 49 / 172

Google 2021 | Confidential and Proprietary | Do not distribute

14. Apply primer on display

15. Aligning display module

● Apply

3M UPUV Primer

around the edges of the

Display module

using a

Dust-free Dust-free Cotton swabs

. Use an

Ionizing air fan

to blow over the device to prepare the Primer for the adhesive.

● Remove the

copper protective film from the blue liner

first.

Part

: G949-00219-01 (Display module),

G806-06032-01 (copper protective film)

● Use the

Universal adsorption-bulb

to prop up the

Display

module.

When apply UPUV primer to the CG module, pay attention to avoid touching

copper and sponge areas (as shown above red figure). Once

Primer

has

been applied, complete assembly in 25 mins.

Display

Summary of Contents for Pixel 6 Pro













































































































































































Search results

Summary of Contents for Pixel 6 Pro

Reviews:

Related manuals for Pixel 6 Pro

Brands by name

Popular brands

Google Pixel 6 Pro, Service Manual

Search results

Summary of Contents for Pixel 6 Pro

Reviews:

Related manuals for Pixel 6 Pro

Brands by name

Popular brands