background image

Goodman Manufacturing Company, L.P.

IO-390A

5151 San Felipe, Suite 500, Houston, TX 77056

6/2011

www.goodmanmfg.com    

www.amana-hac.com

©

 2010 - 2011 Goodman Manufacturing Company, L.P.

I

NSTALLATION

 I

NSTRUCTIONS

F

OR

 S

ELF

-C

ONTAINED

 P

ACKAGE

A

IR

 C

ONDITIONERS

 

AND

 H

EAT

 P

UMP

 U

NITS

GPC/GPH 13 SEER “H” SERIES

RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.

ATTENTION INSTALLING PERSONNEL

IMPORTANT NOTE: These units are shipped WITHOUT REFRIGERANT and are pressurized with a

nitrogen holding charge which must be removed prior to system charging and start up.

Prior to installation, thoroughly familiarize yourself with this Installation Manual. Observe all safety warnings.

During installation or repair, caution is to be observed.

It is your responsibility to install the product safely and to educate the customer on its safe use.

All information contained herein is subject to change without notice.

*NOTE:  Please contact your distributor

or our website for the applicable

Specification Sheets referred to in

this manual.

These installation instructions  cover  the 

outdoor 

installation of self con-

tained package air conditioner and heating units.  See the Specification
Sheets applicable to your model for information regarding accessories.

Summary of Contents for GPC 13 SEER H Series





















Reviews: