PRODUCT IDENTIFICATION
12
MODEL #
MFG #
DESCRIPTION
AFE18-60A
N/A
Fossil Fuel Kit.
The AFE18-60A control is designed for use where the indoor coil is located
above/downstream of a gas or fossil fuel furnace when used with a heat pump. It will operate
with single and two stage heat pumps and single and two stage furnaces. The AFE18-60A
control will turn the heat pump unit off when the furnace is turned on. An anti-short cycle feature
initiates a 3 minute timed off delay when the compressor goes off.
AMU1620
AMU1625
AMU2020
AMU2025
GMU1620
GMU1625
GMU2020
GMU2025
P1251305F
P1251306F
P1251307F
P1251308F
N/A
Media Air Cleaner
. For use with current architectural grey Goodman® and Amana® Brand 80%
and 90% variable speed furnace models. The Amana (AMU*) and Goodman (GMU*) Media Air
Cleaner is a high efficiency air filtration device designed to remove dirt, dust, pollen and other
microscopic particles from the air passing through it. Flexible performance range up to 2,000
CFM capacity. The air cleaner should be installed in the system so that all the system air is
circulated through the air cleaner. The air cleaner will only remove the airborne contaminants
delivered to it. Maximum performance is obtained when the system blower is set for continuous
operation. Carbon filters (optional) are available.
ASAS-10
ASAS-11
ASAS-12
ASAS-18
P1251301F
P1251302F
P1251303F
P1251304F
Electronic Air Cleaner
. For use with current architectural grey Goodman® and Amana® Brand
80% and 90% variable speed furnace models. The High-Efficiency Electronic Air Cleaner is
designed to remove air contaminants down to .01 microns. Carbon filters (optional) remove
odors. Dual indicator lights show unit operation at a glance. Electronic proving switch cycles the
air cleaner On/Off with the system fan. Durable powder-coat paint finish resists corrosion.
CFB17
CFB21
CFB24
P1228004F
P1228005F
P1228003F
Downflow Subbase Kit
. For use with select Goodman®, Amana® Brand & Amana®
Distinctions™ Brand furnace models
ACS9, ACV9, DCS9, GCH9, GCS9, GCV9
.
These kits are
available for the following furnace widths: 17.5" wide (CFB17), 21" wide (CFB21) and 24" wide
(CFB24). The kits must be used to prevent excessive temperature from reaching combustible
materials, if the furnace is installed on a combustible floor. This subbase effectively separated
the furnace base and plenum from combustible materials. To ensure safe installation, do not
install the counterflow floor base directly on carpeting, tile, or other combustible material other
than wood flooring.
DCVK-20
DCVK-30
P1254001F
P1254002F
Concentric Vent Kit
. For use with Amana® Brand furnace models
ACS9, AMS9, AMS95,
ACV9, AMV9, AMH95, DCS9, DMS9, GCS9, GMS9, GMS95,GCH9, GKS9, GCV9,
GMV9,GMH95, GMV95
.
This kit is designed to allow terminations of a direct vent furnace to be
"concentrically" vented through a wall or roof. This kit allows a single penetration to support
terminations for both the vent/flue and the combustion air intake pipe. The DCVK-20 (2") and
DCVK-30 (3") kits are certified for models listed above. See specification sheets on future
models for use of the vent kit.
0170K00000S
N/A
Side Wall Only Concentric Vent Kit
. For use with 90% furnace models
ACS9, AMS9, ACV9,
AMV9, AMH95, DCS9, DMS9, GCH9, GCS9, GKS9, GMS9, GCV9, GMH95, GMV9, GMV95
.
This kit is to be used with 2" or 3" vent systems. The vent kit must terminate outside the
structure. This kit is NOT intended for use with single pipe (indirect vent) installations.