Gold's Gym GGBE29922 User Manual Download Page 20

Bench

Bench Cable W

eight Rest

Safety Spotter

Exercises

Follow these steps when preparing for
each exercise:

1. Adjust the position of the bench

(be sure the bench cable is attached to
the low cable when performing any of
the bench exercises)

2. Adjust the position of the weight rests
3. Attach your barbell to the high cable
4. Adjust the position of the safety spotter 
5. Add weight to the barbell.

The first time you perform the exercises 
listed in the chart, note the position of the
weight rests and safety spotter in the
appropriate column. 

The Bench can be:
R
- removed
D- attached in a declined position
L- attached in a level position
I#- attached in one of five incline positions 

(I1 indicates the least incline; 
I5 indicates fully inclined.)

The Bench Cable can be:
A
- attached
N- not attached

The Weight Rests can be adjusted to 
positions 1–8.
Note the number of the position that is best
for each exercise. 

The Safety Spotter can be adjusted to 
positions A–O
.
Note the letter of the position that is best
for each exercise. 

20

BENCH ADJUSTMENT CHART

The chart below contains a list of exercises that require the use of the safety spotter. When preparing the weight
bench for one of these exercises, follow the steps listed below. For information about each of these steps, refer
to the ADJUSTMENTS section of this manual. Make sure the bench cable is attached to the low cable when
performing any of the bench exercises.

For each exercise, determine the positions of the bench, the weight rests, and the safety spotter that are best for
you. The first time you perform each exercise, write the positions of the weight rests and the safety spotter in the
chart. Write the number corresponding to the height of the weight rests and the letter corresponding to the
height of the safety spotter in the appropriate column. When preparing to perform the exercise again, refer back
to the chart for a quick reference to your personal settings. 

Decline Bench Press

D

A

Bench Press

L

A

Incline Bench Press 1

I1

A

Incline Bench Press 2

I2

A

Incline Bench Press 3

I3

A

Incline Bench Press 4

I4

A

Military Press

I5

A

Squat

R

N

Summary of Contents for GGBE29922




























Reviews: