background image

Operating your Fan 

2 = Medium Speed 

3 = High Speed 

 

Fan control switch 

The control switch positions are: 

• 0 = OFF 

• 1 = Low Speed 

 

Check that the Fan control switch is set to the 
off  position  before  plugging  into  the  mains 
supply.  

 

Place  the  Fan  on  a  dry,  level  and  sturdy 
surface. 

 

Plug  the  power  cord  into  the  socket,  making 
sure the speed control is at OFF position. 

 

To  operate  the  fan  push  down  speed  control 
desired. 

 

Adjust  tilt  by  turning  neck  screw  and  tilting 
body to the  desired wind  direction (i.e. either 
upward or downward).  

 

To  activate  the  oscillation  function,  push 

down  the  oscillation  pin  on  the  top  of  the 
motor. The fan will then oscillate until the pin 
is pulled back up. 

Assembly 

Firstly,  loosen  and  remove  the  four  screws 
from  the  bars.  Then  interlock  cross  bars  A 
and  B.  Be  sure  to  align  the  four  holes  in  the 
bars  with  those  on  the  flange  of  the  Outer 
Tube.  Secure  the  flange  to  the  bars  with  the 
four screws. 

 

Loosen  and  remove  the  Height  Adjustment 

Collar  from  the  top  of  the  Inner  Tube.  Slide 

the  Base  Decorative  Cap  down  over  the 
assembly.  Replace  the  Height  Adjustment 
Collar on top of the Inner Tube. Pull the Inner 
Tube  out  from  the  Outer  Tube  to  adjust  the 
tube  to  the  desired  height  and  tighten  the 
collar. 

 

If necessary, slightly loosen the Set Screw by 
turning  it  anticlockwise.  Slide  the  Switch  Box 
down over the Inner Tube and tighten the Set 

Screw.  Make  sure  the  Set  Screw  is  tightly 

secured. 

Blade and grill 

Unscrew  the  plastic  mounting  nut  from  the 
front  of  the  motor  housing  by  rotating  it 
anticlockwise.  Position  the  rear  grill  against 

the front of the motor housing with the handle 

at  the  top,  ensure  that  the  locating  pegs  on 
the  motor  housing  are  engaged  correctly  in 
the holes of the rear grill.  
 
 
 
 
 
 
Tighten  the  Rear  Grill  Mounting  Nut 

clockwise; do not to over tighten. 

 

Push  the  fan  blade  onto  the  motor  shaft, 
locating  the  slot  at  the  back  of  the  blade  on 
the  drive  pin  that  passes  through  the  motor 
shaft.  Tighten  the  blade  cap  by  turning  it 
anticlockwise. 
 
 
 
 

 

 

Position the front grill against the rear grill so 

that  the  holes  in  the  rims  that  accept  the 

small  nut  and  bolt  are  in  line.  Insert  the  bolt 
through  the  holes  and  screw  on  the  nut.  Do 
not fully tighten at the stage. 
Push  the  grill  retaining  clips  into  position 
ensuring  that  they  engage  correctly  on  the 
rim of the grill. 

 

Fully  tighten  the  small  nut  and  bolt  that 
passes through the rim of the grill. 

Summary of Contents for Venti GCPF110







Reviews: