HEAT CONTROLS
Check that the heat control switch at the back of the heater
is set to the Off position before plugging the heater in and
turning on the mains supply.
Turn the Power Switch at the back of the heater to the
“I”
position. You will hear a beep and the LCD display will
illuminate.
Press the On/Off button on the top of the heater to turn the
heater on. The LCD will display the current room
temperature and begin to blow room temperature air.
Press the Mode button and fan will begin to operate in Low
Heat Mode.
Press the Mode button a second time and the fan will
operate in High Heat Mode.
Press the Button a third time and the unit will indicate
“Auto”;
In this setting you can use the
“+” and “-” buttons on the top
of the unit to adjust the temperature to your desired setting.
To turn the unit off, press the On/Off Button first and then
turn the power switch at the back of the heater to
“O”
position.
For greater economy, use the High Heat setting initially and
then switch to the Low Heat setting.
For the Low and High Heat settings, the fan remains at the
same speed; only the element changes to create the
greater/lesser heat output.
THERMOSTAT
When the air temperature reaches 3
°C
above the desired
set temperature (see
“Auto” Mode above), the heater will
turn off. When the air temperature reaches 1
°C below the
desired set temperature (see
“Auto” Mode above) the
heater will come back on.
The Heater will now cycle on and off to maintain the set
desired temperature.
OSCILLATION
The Oscillating function will work in any mode. Press the
“OSC” button once and the unit will begin to oscillate left
and right. Press the
“OSC” button again and the oscillation
will stop.
TIMER
The Timer function will work in any mode. The Timer
function allows you to set the length of operation time from
1 to 8 hours in 1hour increments. Press the
“Time” button
once and the LCD unit will indicate that 1hour has been set.
The set time can be increased by pressing the
“Time”
Button again, each time the button is pressed the time will
increase by 1hour.
Always choose a safe location for the heater, keeping in mind the safety
precautions outlined. Ensure all packaging has been removed from the unit
before use. This appliance requires no installation, it should be used solely as a
portable appliance.
WARNING Keep all objects at least 1 metre from the front,
sides and rear of the appliance.
SAFETY DEVICE
This appliance has three protection devices:
The first device will automatically turn the appliance off if
the appliance is not in the appropriate operating position.
The second device, automatically disconnects & reconnects
the appliance at a preset temperature.
The third device disconnects the appliance permanently in
case of overheating, by means of a thermal fuse (It is non
resettable).
CAUTION: The Ceramic Heater generates heat during use.
Proper precautions must be taken to prevent the risk of
burns, scalds, fires or other damage to persons.
Do not use this heater with a programmer, remote-control
system, separate timer or any other device that switches
the heater on automatically.
IMPORTANT! NEVER COVER THIS HEATER!
CARE AND CLEANING
The heater requires regular cleaning to ensure trouble free
operation:
Unplug the heater from the mains supply before cleaning.
Ensure that the heater has been allowed to cool down
completely before cleaning.
Use a damp cloth (not wet) to wipe the exterior of the
heater to remove dust and dirt.
Use a vacuum cleaner to remove dust and fluff from around
the grills.
Never use solutions such as benzene, thinners or polishing
agents.
Ensure the heater is dry before plugging back into the
mains supply.
Do not attempt to dismantle the Ceramic Heater. There are
no user serviceable parts. For service or repair, contact an
authorised electrical service technician.
PROOF OF PURCHASE
To receive warranty retain receipt as proof of purchase.
Refer to back of booklet.
Operating your Ceramic Heater
Goldair
– New Zealand
Monday
– Friday 8am-5pm
Phone +64 (0)9 917 4000
Phone 0800 232 633
[email protected]
Goldair
– Australia
Monday
– Friday 8am-5pm
Phone +61 (0)3 9336 4423
Phone 1300 465 324
SUPPORT AND TECHNICAL ADVICE
