manualshive.com logo in svg

GOG eXTCy Series, Operation Instructions Manual, Page: 22 / 34

Share
Download
GOG eXTCy Series Operation Instructions Manual Download Page 22

                                        GOGpaintball.com   

 

If removing the breech from the body cover, the Vision

TM

 wiring harness must be removed first. Uncoil the Vision

TM

 wires and remove both eyes from their pockets (see 

Vision

TM

/detent cleaning). Carefully twist each eye so that its dome shaped lens faces forward and guide it down through the slot in the beech and out the bottom of the body 

shell, gently pulling its wires ahead of it so they do not bind.

Slide the breech out the back of the body cover. Carefully clean any paint or debris from the breech and body cover

The circuit board may then be carefully lifted away from the body and breech. 

After sliding the breech back into place, the Vision

TM

 wiring harness and eyes are reinstalled via the same openings through which they were removed. Coil the Vision

TM 

wires 

into their pocket as shown before reinstalling the circuit board.

FIG. 19

SLIDE BREECH OUT BACK 

ADVANVED MAINTENANCE

CONTINUED

19

FIG. 20

COILED VISION

TM

 WIRES

FIG. 18

ROTATE AND REMOVE EYES

Summary of Contents for eXTCy Series



































Reviews:

No comments