Godox XProC Instruction Manual Download Page 3

Warning

Do not disassemble. Should repairs become necessary, this product must be sent to 

an authorized maintenance center.

Always keep this product dry. Do not use in rain or in damp conditions.

Keep out of reach of children.

Do not use the flash unit in the presence of flammable gas. In certain circumstance, 

please pay attention to the relevant warnings.

Do not leave or store the product if the ambient temperature reads over 50

℃.

Turn off the flash trigger immediately in the event of malfunction.

Observe precautions when handling batteries

   - Use only batteries listed in this manual. Do not use old and new batteries or 

     batteries of different types at the same time.

   - Read and follow all warnings and instructions provided by the manufacturer.

   - Batteries cannot be short-circuited or disassembled.

   - Do not put batteries into a fire or apply direct heat to them.   

   - Do not attempt to insert batteries upside down or backwards.

   - Batteries are prone to leakage when fully discharged. To avoid damage to the 

     product, be sure to remove batteries when the product is not used for a long time or 

     when batteries run out of charge.

   - Should liquid from the batteries come into contact with skin or clothing, rinse 

     immediately with fresh water.

Names of Parts

Body

Power Switch

--ON  (

Power On)

--OFF (

Power Off)

AF Assist Beam Switch

--

ON (AF Assist Beam outputs)

--

OFF (AF Assist Beam 

do not output)

Battery Compartment

Hot Shoe Camera Connection

LCD Panel

Status Indicator Lamp

   --

Green: 

        

Trigger (Flash) + 

        Focus (Camera)

    --

Red: 

        

Trigger (Flash) + 

        Shutter (Camera)

Group Button 1

Group Button 2

Group Button 3

Group Button 4

Group Button 5

Function Button

 

2

Function Button1

Function Button

 

3

Function Button

 

4

MODE/LOCK Mode Selection/
Locking Button

TEST/Shutter Button

MENU Button

Magnification/TCM Button

Select Dial

2.5mm Sync 
Cord Jack

Type-C USB
Port

AF-assist Lamp

- 25 -

- 26 -

Summary of Contents for XProC















Reviews: