Godox XProC Instruction Manual Download Page 10

1.  

        High-speed sync: press the <

SYNC

> button and      

      is displayed        on the LCD panel.

2. 

         Second-curtain sync: press the <    > on Nikon 

     camera, and turn the main command dial until         is 

     displayed on the panel. Then, set the camera shutter. 

Shutter Sync Settings

Press the <

MENU

> button to enter C.Fn BEEP and press 

the <

SET

> button. Choose ON to turn on the BEEP while 

OFF to turn off it. Press the <

MENU

> button again to back 

to the main menu.

Buzz Settings

1. 

 Press the <

MENU

> button to enter C.Fn SYNC and 

    press the <

SET

> button to choose IN or OUT. Press 

    the <

MENU

> button again to back to the main menu.

   

 1.1

 

 

When choosing IN, this sync socket will enable 

          XProN to trigger flash.

    

1.2

 

 

When choosing OUT, this sync socket will send 

          trigger signals to trigger other remote control and 

          flash.

Sync Socket Settings

TCM transform function is a particular 

function that owned by Godox: 

TTL flash value  transform into     

power output value in M mode.

   1.1 

 Set the flash trigger to TTL mode 

         and attach it to the camera. 

         Press the shutter for shooting.

   1.2 

 Long press the <

TCM

> button, and the flash value in TTL mode will 

         transform into power output value in M mode (The displayed minimum value 

         is the set Min. value). 

   1.3

 Please refer to the C.Fn setting custom functions to see the flash models 

         which are compatible with TCM functions.

          Note

:

Please choose the relevant models in TCM function in C.Fn custom settings according 

          to your own flash.  

TCM Function

Setting the Flash Trigger 

Setting the Flash Trigger 

ZOOM Value Settings

Long press the <

CH/Zm

> button for 2 seconds and the 

ZOOM value will be displayed on the LCD panel. Choose 

the group and turn the select dial, and the ZOOM value will 

change from AUTO/24 to 200. Choose the desired value 

and long press the <

CH/Zm

> button again to back to the 

main menu.

Note: The flash’s ZOOM should be set to Auto (A) mode before 

responding.

CH1

CH/Zm

SYNC

MOD

Zoom  28

A

B

C

D

E

Zoom  24

Zoom  24

Zoom  24

Zoom  24

CH1

A

B

C

D

E

--

M

1

/16 + 0.3

--

--

--

CH/Zm

SYNC

ALL

MOD

C.Fn

Ver 9.2

OFF
ON

CLEAR

MIN

LIGHT

STBY

BEEP

C.Fn

Ver 9.2

GROUP

LCD

SHOOT

SYNC

IN
OUT

CLEAR

- 40 -

- 39 -

REAR

CH1

CH/Zm

SYNC

MOD

A

B

C

D

E

ALL

--

TTL

--

--

--

CH1

CH/Zm

SYNC

MOD

A

B

C

D

E

ALL

--

M

--

--

--

1/

128

Summary of Contents for XProC















Reviews: