GMP Air Stream 89300 Operation And Maintenance Download Page 33

Page: 33 / 41

Page 33 of 41

APPENDIX 1

This section lists the appropriate inserts collets etc required for a given cable/tube combination.

TUBE COLLET AND CLAMP ASSEMBLIES

89310

TUBE COLLET AND CLAMP ASSEMBLY 05 mm O.D.

89311

TUBE COLLET AND CLAMP ASSEMBLY 07 mm O.D.

89312

TUBE COLLET AND CLAMP ASSEMBLY 08 mm O.D.

89313

TUBE COLLET AND CLAMP ASSEMBLY 10 mm O.D.

89314

TUBE COLLET AND CLAMP ASSEMBLY 12 mm O.D.

89315

TUBE COLLET AND CLAMP ASSEMBLY 12.7 mm O.D.

89316

TUBE COLLET AND CLAMP ASSEMBLY 14 mm O.D.

89317

TUBE COLLET AND CLAMP ASSEMBLY 16 mm O.D.

CABLE GUIDE ASSEMBLIES

89305

CABLE GUIDE, 2.5mm DIAMETER

89306

CABLE GUIDE, 2.5 TO 3.0mm DIAMETER

89307

CABLE GUIDE, 3.0 TO 6.4mm DIAMETER

CABLE SEAL COLLET ASSEMBLY

89374

CABLE SEAL COLLET ASSEMBLY 2.5 TO 3.0 mm DIAMETER

89375

CABLE SEAL COLLET ASSEMBLY 3.0 TO 3.8 mm DIAMETER

89376

CABLE SEAL COLLET ASSEMBLY 3.8 TO 5.0 mm DIAMETER

89377

CABLE SEAL COLLET ASSEMBLY 5.0 TO 6.4 mm DIAMETER

89378

CABLE SEAL COLLET ASSEMBLY 6.4 TO 8.0 mm DIAMETER

89379

CABLE SEAL COLLET ASSEMBLY 8.0 TO 9.5 mm DIAMETER

SPARE CABLE SEAL

89510

CABLE SEAL 2.5 TO 3.0 mm (PACK OF 5)

89511

CABLE SEAL 3.0 TO 3.8 mm (PACK OF 5)

89512

CABLE SEAL 3.8 TO 5.0 mm (PACK OF 5)

89513

CABLE SEAL 5.0 TO 6.4 mm (PACK OF 5)

89514

CABLE SEAL 6.4 TO 8.0 mm (PACK OF 5)

89516

CABLE SEAL 8.0 TO 9.5 mm (PACK OF 5)

DRIVE BELTS (sold in pairs)

30952

DRIVE BELT, 3-11 mm DIAMETER CABLE

30953

DRIVE BELT, 1-5 mm DIAMETER CABLE

SPARE TUBE SEAL O RING

89549

TUBE SEAL O RING 05 mm DIAMETER (PACK OF 5)

89553

TUBE SEAL O RING 07 mm DIAMETER (PACK OF 5)

89550

TUBE SEAL O RING 08 - 8.5mm DIAMETER (PACK OF 5)

89551

TUBE SEAL O RING 10 mm DIAMETER (PACK OF 5)

89552

TUBE SEAL O RING 12 - 12.7 mm DIAMETER (PACK OF 5)

89554

TUBE SEAL O RING 16 mm DIAMETER (PACK OF 5)

SPARE CORD SEAL

89691

SEAL CORD 2 mm DIAMETER X 3’ (1M) LONG

89318

TUBE COLLET AND CLAMP ASSEMBLY 18 mm O.D.

89558

TUBE SEAL O RING 18 mm DIAMETER (PACK OF 5)

89303

CABLE GUIDE, 6.0 TO 8.5mm DIAMETER

89373

CABLE SEAL COLLET ASSEMBLY 9.5 TO 11.0 mm DIAMETER

89517

CABLE SEAL 9.5 TO 11.0 mm (PACK OF 5)

89304

CABLE GUIDE, 8.5 TO 11mm DIAMETER

89555

TUBE SEAL O RING 14 mm DIAMETER (PACK OF 5)

Summary of Contents for Air Stream 89300










































Search results

Summary of Contents for Air Stream 89300

Reviews:

Related manuals for Air Stream 89300

Brands by name

Popular brands

GMP Air Stream 89300, Operation And Maintenance

Search results

Summary of Contents for Air Stream 89300

Reviews:

Related manuals for Air Stream 89300

Brands by name

Popular brands