Installation of child safety seat into vehicle
4. Installation of child safety seat into vehicle
WARNING:
Never leave a child in the child safety seat unattended in the vehicle.
WARNING
: To protect everyone in the car when driving:
In the event of an accident or emergency braking persons without fastened seat belts or unsecured
items may cause injury to other passengers in the vehicle. This is why you should please check that:
•
Seat backrests are locked in their standard driving position (i.e. for example folding central
section of the back seat is locked in).
•
All heavy objects or items with sharp edges in the vehicle (e.g. shelves, etc.) are secured.
•
All passengers in the vehicle have fastened seatbelts in each individual seat
•
Child safety seat is always secured, if in the vehicle, even if no child is transported.
To protect the vehicle:
Some seat covers, made from sensitive materials (e.g. velvet, leather, etc.), can
experience formation of creases from the child safety seat. This can be prevented by placing a
blanket or a towel
under the child safety seat.
ISOFIX anchoring parts and Top Tether
4. 1 Child safety seat installation for Group I in the weight category 9-18 kg using the
ISOFIX anchorage and Top Tether
Important:
First check that there are two ISOFIX anchors in the vehicle vertical to the child safety seat, between
vehicle seat's back rest, and whether behind the vehicle's seat there is a buckle anchor, ready to be
used.
Tip:
Usually the anchoring system to hook the buckle is found on the inside of the luggage area
on the floor of the vehicle. You may get information from the vehicle's owner's manual, issued by its
manufacturer.
Press the ISOFIX button to release and pull out the ISOFIX connector as far as back as possible
(Fig.13). Press the ISOFIX connectors and direct them into the anchors until you hear a clear
clicking sound (Fig. 14, 15).
Grab the child safety seat and check whether it is properly attached and is not loose. (Fig. 16)
If the safety seat is loose and ISOFIX connectors are pulled out, please repeat the above stated
process and reinstall the child safety seat
NOTICE!
Check that between child safety seat and the vehicle's seat or between
doors there are no objects
Pull out the handle (Top Tether), (Fig. 17) and press the harness release button to pull out the strap
to desired length (Fig. 18), to enable you to hook the latch to the back ready anchoring vehicle
element.
Hook the harness latch (Top Tether) into the anchor (Fig. 19). Check available vehicle anchors,
because there may be several. Select the most appropriate anchor to install the child safety seat
(Fig. 20).
NOTICE!
To find the child safety seat's connection point Top Tether look into the vehicle's owner's
manual.
This anchoring point is designated with an appropriate label, and can be found in places marked
in the picture (Fig. 20).
Pull on the Top Tether strap on the other end and tighten it (Fig. 21).
Notice:
If the Top Tether system is properly tightened, on the other end of the button to release the
harness you will see a green guide mark
Please check for the presence of a green marker on the harness (Fig. 22).
NOTICE!
Pull the Top Tether between the top part of the vehicle backrest and the headrest. Never
pull the Top Tether through above the vehicle's headrest
Summary of Contents for GM1709
