![background image](http://html.mh-extra.com/html/gmc/tech2/tech2_user-manual_2235895122.webp)
General Motors Tech2 User Guide
122
Note: If calibrations are the same, the NAODRUI Control box appears stating that
the calibrations selected are already the current calibrations in the control module.
Click OK and Back out or click Cancel on the Summary screen.
2.12
The application will automatically initiate the download of the new calibration file to
the Tech2, and a Transfer Data screen will track the progress of the download.
2.13
After the download is complete, a Program Controller screen will appear with
instructions for connecting the Tech2 to the vehicle to complete the programming
process. Close the application to return to the TIS2Web Application Selection
screen, then power down and disconnect the Tech2 from the PC.
Controller Specific Instructions
If “Crankshaft Position Variation Relearn Procedure” appears under “Controller Specific
Instructions,” you must perform this procedure after reprogramming the PCM/VCM.
STEP 3: Transfer Data from the Tech2 to the Control Module
3.1
With the Tech2 and vehicle both off, connect the Tech2 to the vehicle DLC.
3.2
Power on the Tech2. At the Tech2 title screen, press [ENTER].
3.3
Turn the vehicle ignition to the “on” position (engine off).
3.4
At the Tech2 Main Menu, select Service Programming System.
3.5
Select "F1: Program ECU" on the Tech2. The Tech2 will display the new
programming data
— VIN and software numbers. Verify, then select the soft key
Continue. The Tech2 will display the "Programming in Progress - Downloading
calibration file" screen.
3.6
When the transfer is complete, the Tech2
will display the message “Programming
Was Successful.” Press the Continue soft key to exit the program. Turn the vehicle
ignition off first, then turn the Tech2 off and disconnect it from the vehicle.
Be sure to verify successful reprogramming.
Verifying Reprogramming
After any kind of control module programming, verify that programming was successful:
Turn the ignition off, wait at least 30 seconds, then start the vehicle to confirm that
reprogramming was successful. If the vehicle does not start or starts but runs rough,
repeat the SPS procedure.
Important
: Some vehicles will require that Idle Learn, TP Learn, Theft Deterrent Relearn,
or Crankshaft Variation Learn procedures be performed after programming. Consult the
appropriate service information for these procedures.
Tech2 SPS User Interface Screens and Functionality
Overview
This section is a representation of the Tech2 Service Programming System (SPS) user
interface screen application. User interface screens that could be encountered during the
Summary of Contents for Tech2
