8
GB
Jigsaw Safety
WARNINGS: Before connecting a tool to a power source (mains switch
power point receptacle, outlet etc.) be sure that the voltage supply is the
same as that specified on the nameplate of the tool. A power source with a
voltage greater than that specified for the tool can result in serious injury to
the user, and damage to the tool. If in doubt, do not plug in the tool. Using
a power source with a voltage less than the nameplate rating is harmful to
the motor.
For safety relating to protective clothing/equipment and general health
hazards relating to power tools; refer to General and Electrical Safety
sections in this manual
• Do not let anyone below 18 years of age operate this jigsaw
• Ensure there is adequate lighting
• Rags, cloths, cord and string etc should not be left around the work
area
• Keep the area free of tripping hazards
• Inspect the workpiece and remove all embedded objects before starting
work
• Support or clamp the workpiece to avoid vibration, and ensure a good
cut
• See specification section of this manual for the correct type of blade.
Incorrect blades may not be secured correctly, causing a safety hazard
• Only use blades that are in good condition
• To avoid the possibility of an electric shock, always hold the saw using
the insulated handles
• If you are interrupted when operating the saw, complete the process
and switch off before looking up
• Keep your hands away from the underside of the workpiece
• Ensure that an appropriate blade is used for the material being cut
Ensure all supports and power cables are completely clear of the
cutting path
• Where guards exist, ensure they are in place
• Do not put pressure on the tool. Allow the blade to cut at its own pace.
This will produce better results and maximise the service life of the tool
• Before cutting, check that there is sufficient clearance for the blade
under the workpiece
• Always keep the shoe pressed against the workpiece
• Do not attempt to cut material thicker than detailed in the specifications
section of this manual
• Do not force the blade to bend or twist whilst cutting
• If a cut does not extend to the edge of the workpiece, allow the blade to
come to a complete stop before lifting it from the workpiece
• Do not use your hands to remove sawdust, chips or waste close by the
blade
• Do not reach over the blade to remove waste or off-cuts
• Blades heat up during use. Allow to cool completely before handling
• If a blade jams, disconnect the machine from the power supply prior to
releasing the blade
• Periodically check that all nuts, bolts and other fixings, tighten where
necessary
Cutting Tool Safety
Use the correct cutting tool
• Ensure the cutting tool is suitable for the job. Do not assume a tool is
suitable without checking the product literature before use
Protect your eyes
• Always wear appropriate eye protection when using cutting tools
• Spectacles are not designed to offer any protection when using this
product; normal lenses are not impact resistant and could shatter
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 85dB
Protect your breathing
• Ensure that yourself, and others around you, wear suitable dust masks
Be aware of others around you
• It is the responsibility of the user to ensure that other people in the
vicinity of the work area are not exposed to dangerous noise or dust
and are also provided with suitable protective equipment
Hidden objects
• Inspect the workpiece and remove all nails and other embedded objects
before cutting
• Do not attempt to cut material that contains embedded objects unless
you know that the cutting tool fitted to your machine is suitable for the
job
• Walls may conceal wiring and piping, car body panels may conceal fuel
lines, and long grass may conceal stones and glass. Always check the
work area thoroughly before proceeding
Beware of projected waste
• In some situations, waste material may be projected at speed from the
cutting tool. It is the user’s responsibility to ensure that other people in
the work area are protected from the possibility of projected waste
Fitting cutting tools
• Ensure cutting tools are correctly and securely fitted and check that
wrenches / adjusters are removed prior to use
• Only use cutting tools recommended for your machine
• Do not attempt to modify cutting tools
920308_Z1MANPRO1.indd 8
24/09/2013 14:15
