Children should be supervised at all times if they are in the
area in which the tool is being used. It is also imperative
that you observe the accident prevention regulations in
force in your area. The same applies for general rules of
occupational health and safety.
The manufacturer shall not be liable for any changes made
to the tool nor for any damage resulting from such changes.
Even when the tool is used as prescribed it is not possible to
eliminate all residual risk factors. The following hazards may
arise in connection with the tool’s construction and design:
• Damage to the lungs if an effective dust mask is
not worn.
• Damage to hearing if effective earmuffs are not worn.
• Damage to eyes if effective goggles are not worn
• Risk of injury unless hands are kept well clear of
cutting devices
Unpacking
Due to modern mass production techniques, it is unlikely
that your GMC Power Tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
Operation
WARNING.
Before connecting a tool to a power source
(power point receptacle, outlet, etc.) be sure that the voltage
supply is the same as that specified on the nameplate of
the tool. A power source with a voltage greater than that
specified for the tool can result in serious injury to the user,
as well as damage to the tool. If in doubt, do not plug in
the tool. Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
Switch on
1. Set the variable speed dial (4) to 1 and push the on/off
switch (3) to “I”, the machine is in continuous operation,
and will start at minimum speed.
Switch off
1. Reset the variable speed dial (4) to 1 and push the on/off
switch (3) to position “0”.
Varying the speed
1. You can use the variable speed dial (4) to alter the speed
of the collet, as follows:
• Position 1 - Slow
• Position 3 - Medium
• Position 6 - Fast
2. Select the correct speed for the work and type of bit
you are using. In general, lower speeds are best suited
for large accessories and higher speed for smaller
accessories.
Quick reference guide
Operation
Speed
• Cutting metal
5 - 6
• Sanding wood
5 - 6
• Cutting hard metal
5 - 6
• Engraving metal
4 - 5
• De-burring
4 - 5
• Drilling holes
4 - 5
• Removing rust
3 - 4
• Sharpening
3 - 4
• Polishing
1 - 2
Holding the tool
1. For jobs such as milling or engraving where precision is
required, hold the tool like a pen.
2. For heavier work like cutting or grinding hold the machine
in the palm of your hand.
Changing accessories
1. Make sure that the machine is switched off and the
plug removed from the power before you commence
changeover.
2. Loosen and tighten collet fully using the 2 in 1
wrench provided. (always ensure bits are tight before
commencing any work with your tool).
3. Press and hold down the spindle lock button (5) and
unscrew the Collet nut (6).
4. Select a suitable Collet for the accessory to be used and
insert it in the collet nut shaft.
5. Turn the Collet nut in an anti-clockwise direction to
loosen and, when the bit is in place, turn the Collet nut in
clockwise direction to lock it in place, whilst depressing
the spindle lock.
6. Make sure that the bit is inserted as far as possible.
Having too much shaft exposed could cause it to damage
or bend.
Locating a cutting/sanding disc
1. Insert the disc holder into the Collet (7) whilst the Collet
nut (6) is loosened.
2. Remove the screw from the end of the disk holder with
the 2 in 1 wrench provided, and insert the screw through
the cutting/sanding disc.
3. Replace the screw and tighten, attaching the cutting or
sanding disc onto the holder. (Do not over-tighten)
Locating a sanding drum
1. Loosen the small screw in the top of the holder
(This allows the rubber to slacken).
2. Slide the sanding drum onto the holder.
3. Secure the sanding drum in place by tightening the
screw causing the rubber drum to bulge and grip the
drum. (Do not over-tighten)
Attaching the flexible shaft
WARNING.
Never bend the flexible shaft with a radius
of less than 150 mm (6”) when operating. Please store the
flexible shaft in the designated compartment of the carry
case when not in use.
1. Remove the collet cover (9), and loosen the collet nut (6)
by turning them anti-clockwise.
2. Insert the inner cable of the flexible shaft into the collet
(7) until the cable cannot go any further.
3. Tighten the collet nut (6) with the wrench by turning the
nut clockwise.
4. Thread the flexible shaft collet cover onto the tool housing
by turning it clockwise, and finger tighten only.
WARNING.
Never tighten the collet nut with the use of
pliers or a wrench as the thread will strip.
Changing the collet and accessories
Note.
To change the collet or install a cutter or accessory
into the flexible shaft, follow the same general procedure as
covered earlier under ‘Changing accessories’.
WARNING.
Do not attempt to loosen the collet nut without
pulling the spindle lock back as far as possible. Damage to
the flexible shaft will result.
1. To lock the spindle lock, pull the lock back as far
as possible.
2. Use the wrench to loosen and tighten the collet nut.
Maintenance
1. Store the machine, instruction manual and, where
necessary, the accessories in the original packaging.
In this way you will always have all the information and
parts ready to hand.
Cleaning
1. Keep the tool’s air vents unclogged and clean at
all times.
2. Remove dust and dirt regularly. Cleaning is best
done with a rag.
3. Never use caustic agents to clean plastic parts.
CAUTION.
Do not use cleaning agents to clean the
plastic parts of the tool. A mild detergent on a damp
cloth is recommended. Water must never come into
contact with the tool.
Repairs
1. Only an authorised service centre should replace the
cordset or effect other repairs. If the cordset is damaged
or worn, have it repaired or replaced by an authorised
service centre.
2. When the brushes are worn, the tool may not work.
Have new brushes fitted by an authorised service centre.
Please refer to your warranty card, which is separate
to these instructions
Accessories For DEC003AC Kit
Sanding
Sanding drums are perfect for detailed sanding jobs.
5 Coarse sanding sheets
20 mm diameter
5 Fine sanding sheets
20 mm diameter
5 Sanding bands
15 mm diameter
Mandrels
1 Mandrel for sanding band 3.2 mm Diameter shaft
1 Disc mandrel for cut-off wheel 3.2 mm Diameter shaft
1 Polishing pad mandrel 3.2 mm Diameter shaft
Grinding
The perfect way to remove burs and sharpen tools.
5 Grinding stones
Various shapes & sizes
Cutting
Various cutting wheels let you cut, trim and shape metal,
glass and ceramics.
1 Ball-shaped high speed cutter
2.4 mm Diameter shaft
1 Corn-shaped cutter
2.4 mm Diameter shaft
8 Cut-off wheels
24 mm Diameter
Polishing & cleaning
Ideal for removing rust, smoothing out imperfections
or cleaning tools.
1 Polishing pads
Felt
13 x 9 mm
1 Polishing pads
Felt
25 x 5 mm
1 Bristle Brush
Brass 3.2 mm Diameter shaft
1 Wire brush wheel
3.2 mm Diameter shaft
Drilling
An extremely convenient way to drill holes with more
detail and precision.
1 High speed drill bit
3.2 mm diameter
1 2 in 1 Wrench
2 Collets
2.4 mm and 3.2 mm
1 Stone for dressing grinding wheels 26 x 10 x 10 mm
45–55 South Centre Road Melbourne Airport
Victoria, Australia 3045
Tel: (03) 8346 1100 Fax: (03) 8346 1200
Full 2-Year Warranty
This product is warranted for a 2-year period for
home domestic use from the date of the original
purchase. If found to be defective in materials
or workmanship, the tool or the offending faulty
component will be replaced free of charge with
another of the same item. A small freight charge
may apply.
The warranty replacement unit is only made
available by returning the tool to the place of
purchase with a confirmed register receipt.
Proof of purchase is essential. We reserve the
right to reject any claim where the purchase
cannot be verified. This warranty does not
include damage or defects to the tool caused by
or resulting from abuse, accidents, alterations or
commercial or business use.
Consistent with our product development
programme, improvements may have been made
which render the contents of the tool’s packaging
or user instructions slightly different to the
product received.
Phone (03) 8346 1100 Facsimile (03) 8346 1200
Email [email protected]
Website www.gmcompany.com
Copyright Global Machinery Company Australia
Proprietary Limited, 2001
Dear customer, if you require any help with your
product, whether it is a Warranty Claim, spare
part or user information, please phone our
Help Line
1300 880 001 (Australia)
or 0800 445 721 (New Zealand), for an
immediate response.
Product of China manufactured to exacting
GMC quality standards.
ABN: 68 093 174 808
The GMC 777 Helpline
operates from 7am to
7pm, 7 days a week (EST).
This allows you to contact GMC directly with
any queries and technical questions you have
regarding our products.
Save this Manual for future reference.
