background image

Warning.

The air filter must be added before first use.

Failure to fit the air filter will damage the compressor and
will void the warranty.
4. Remove the plastic air filter plug from the head of the

compressor.

5. Carefully screw the air filter assembly (16) into the

threaded hole taking care not to cross the thread.

6. Tighten firmly by hand only.

Pre-start routine

1. Ensure that the location for the compressor is clean,

dry and well ventilated.

2. Ensure the crank case has been filled with oil and is at

the correct level, and the air filter has been fitted.

3. Open the direct output valve (4) and the regulated

output valve (7).

Open the valve by sliding the outer sleeve fully forward.
To close the valve, slide the outer sleeve backward
towards the compressor.

4. Start the compressor by following the procedure in the

section “To start and stop the compressor”. For the first
time of operation, run the compressor for 10 min with
no load to ensure all parts are well lubricated.

Warning.

Be aware that presurised air will be discharged

from the two outlets and care should be taken that this
discharge is not directed towards you the operator, or
other persons within the area.

To start & stop the compressor

1. Check the rating label on

the compressor indicates
230V–240V.

2. Plug in the mains cable of

the compressor to a
standard 240V houshold
power point and turn on.

3. To start  the compressor,

lift the On/Off switch (3)
on the pressure switch
cover (2).

4. To stop the compressor,

push the On/Off switch
(3) down.

11

Summary of Contents for AC24L

















Reviews: