Glow-worm Ultimate 3 30c Operating Instructions Manual Download Page 13

Care and maintenance 6

0020239565_01

 

Ultimate

 

3

 

Operating

 

instructions

13

5.2 Fault codes in the display

Fault codes have priority over all other dis-

plays. If several faults occur at the same

time, the corresponding codes are dis-

played alternately for two seconds each.

If your product displays a fault code

(F.xx), contact a competent person.

6 Care and maintenance

6.1 Maintenance

An annual inspection of the product carried

out by a competent person is a prerequis-

ite for ensuring that the product is perman-

ently ready and safe for operation, reliable,

and has a long working life.

6.2 Caring for the product

Caution.
Risk of material damage
caused by unsuitable clean-
ing agents.

Do not use sprays, scouring

agents, detergents, solvents

or cleaning agents that con-

tain chlorine.

Clean the casing with a damp cloth and

a little solvent-free soap.

6.3 Checking the condensate

drain pipework and tundish

The condensate drain pipework and tun-

dish must always be penetrable.

Regularly check the condensate drain

pipework and tundish for faults and,

particularly, for blockages.

You must not be able to see or feel any

obstructions in the condensate drain pipe-

work and tundish.

If you notice a fault, have it rectified by

a competent person.

7 Decommissioning

7.1 Temporarily decommissioning

the product

Temporarily decommission the product

only if there is no risk of frost.

Switch off the product via the main

switch provided on-site.

The display goes out.

When decommissioning for an exten-

ded period (e.g. holiday), you should

also close the gas isolator cock and the

cold water stop cock.

7.2 Permanently

decommissioning the product

Have a competent person permanently

decommission the product.

8 Recycling and disposal

The competent person who installed

your product is responsible for the dis-

posal of the packaging.

If the product is identified with this

symbol:

In this case, do not dispose of the

product with the household waste.

Instead, hand in the product to a collec-

tion centre for old electrical or electronic

appliances.

If the product contains batteries that

are marked with this symbol, these bat-

teries may contain substances that are

hazardous to human health and the envir-

onment.

In this case, dispose of the batteries at

a collection point for batteries.

Summary of Contents for Ultimate 3 30c





















Reviews: