background image

             

 

EM-318-01

                                                                                               

 

Specifications are subject to be changed without notice. 

Page 5 of 16 

 

Version 1.2.2 

„

 

Pin Assignment

 

 

                                 

 

 

Pin #  Name 

Description 

VCC_IN 

DC Supply Voltage input 

GND Analog 

Ground 

1PPS 

One Pulse per second output synchronized to GPS time. Not available in 

trickle mode. 

BOOTSEL 

Boot mode – set high to program flash 

TXA 

Serial output for channel 

RXA 

Serial input for channel 

GPIO1 

GPS Fix status output 

VBAT 

Backup voltage supply 

This is the battery backup input that powers the SRAM and 

RTC when main power is removed. Typical current draw is 15uA. Without an external 

backup power supply, the GPS module/engine board will execute a cold star upon 

each power-up.    To achieve the faster start-ups a backup must be connected to this 

pin (battery or Gold /Super capacitor). The voltage should be between 2.0v and 5.0v

(

NOTE

:

 

The VBAT pin must be kept “

HIGH

” for in order for the GPS board/module to 

function if no backup power is going to be used. From the VCC, connect a 470 Ohm ¼ 

Watt resistor in series with a 3.2v Zener diode to Ground. Connect the VBAT pin to the 

Zener’s cathode to pull the input “

HIGH

”.)

 

NRESET 

Reset Input (Active Low) 

10 

NC Not 

connect 

Summary of Contents for EM-318-01

















Reviews: