background image

             

 

EM-318-01

                                                                                               

 

Specifications are subject to be changed without notice. 

Page 15 of 16 

 

Version 1.2.2 

 

E.) LLA Navigation initialization ID:104      Parameters required to start using Lat/Lon/Alt 

 

 

This command is used to initialize the GPS module for a “Warm” start, providing real-time position 
(Latitude, Longitude, Altitude coordinates), clock offset, and time. This action enables the GPS 
receiver to search for the necessary satellite signals at the correct signal parameters. The newly 
acquired and stored satellite data will enable the receiver to acquire signals more quickly, and thus, 
generate a rapid navigational solution. 

 

 

When a valid LLA Navigation Initialization command is receive, then the receiver will restart using the 
input parameters as a basis for satellite selection and acquisition. 

 
Format: 
$PSRF104,<Lat>,<Lon>,<Alt>,<ClkOffset>,<TimeOfWeek>,<WeekNo>, 
<ChannelCount>, <ResetCfg>*CKSUM<CR><LF> 

 

 

<Lat>                     

 

Latitude position, assumed positive north of equator and negative 

south of equator float, possibly signed 

 
 

<Lon>                    

Longitude position, it is assumed positive east of Greenwich 

 

 

and negative west of Greenwich Float, possibly signed 

 
      <Alt>           

 

Altitude position float, possibly signed 

 
            <ClkOffset>         

 

Clock Offset of the receiver in Hz, use 0 for last saved value if 

available.  

 

If this is unavailable, a default value of 75000 for GSP1, 95000 for GSP1/LX 
is used. 

                                         

 

INT32 

 

<TimeOfWeek>       

GPS Time Of Week   

                                         

 

UINT32 

          <WeekNo>               

GPS Week Number 

                                         

 

UINT16 

 

<ChannelCount>     

Number of channels to use. 1-12 

                                         

 

UBYTE 

 

<ResetCfg>      

bit mask    

 

 

 

   0×01=Data 

Valid 

warm/hot 

starts=1 

                             

0×02=clear ephemeris warm start=1 

                                                         

0×04=clear memory. Cold start=1 

                                                         

UBYTE 

Example: Start using known position and time. 
$PSRF104,37.3875111,-121.97232,0,96000,237759,922,12,3*37 
 

F.) Development Data On/Off ID:105      Switch Development Data Messages On/Off 

 

 

Use this command to enable development debug information if you are having trouble in attaining 
commands accepted. Invalid commands will generate debug information that should enable the    user   
to determine the source of the command rejection. Common input rejection problems are associated 
to invalid checksum or parameter out of specified range. Note, this setting is not preserved across a 

Summary of Contents for EM-318-01

















Reviews: