background image

March 2019 

 

Page 1 

Ultra E Lock User Instructions 

The Global Link Ultra E Lock features: 

  Convenient handle design, available in both right- and left-handed models 

  Illuminated keypad for keyless entry 

  Beep feedback indicating success and failure of actions as well as low battery conditions 

  Easy installation in standard door cutouts and direct replacement for standard travel 

trailer entrance locks from: 

  FIC / Wesco 

  Bauer 

  TriMark 

  Support for two access codes—a factory default code and a customer code 

  Interior safety release button for emergency exit 

  Customer key access for alternative operation of the lock 

  Can be keyed-alike to match other Pro Series locks 

The lock is powered by a single Type 123 lithium battery and operates with a 4-digit code. Each 
lock has a factory default code that can be used at any time and cannot be erased; 1 additional 
customer code can be added. 

Important

: Before using the lock, record the default 4-digit code printed on a label affixed to the 

inside handle of the lock. The factory default code is needed for keyless entry before a customer 
code has been added and to program / reprogram the customer code. 

 

Figure 1: Global Link Ultra E Lock 

 WARNING

: Cancer and Reproductive Harm – 

www.P65Warnings.ca.gov

.

 

 

Summary of Contents for Ultra E Lock









Reviews: