manualshive.com logo in svg

GlassCrafters EPIC By-Pass Sliding Doors, Installation Instructions Manual

Share
Download
GlassCrafters EPIC By-Pass Sliding Doors Installation Instructions Manual Download Page 13

17

It is essential that Silicone Sealant be applied at
all locations indicated by dotted lines, as shown in

SKETCH 17 A.

Please note :

 After applying Silicone

Sealant, it must not be used for 24 hours
to allow the sealant to set properly.

Apply Silicone Sealant

   Inside and Outside

SKETCH 17 B

.

Apply Silicone Sealant as shown

Be sure to add Silicone to both ends of the Base
where it meets the Wall , as shown in

SKETCH 13 A.

Please note that after applying Silicone
Sealant, it must not be used for 24 hours
to allow the sealant to set properly.

It is essential that Silicone Sealant be applied at
all locations indicated  inside and outside,
as shown in 

SKETCH 17 B.

Apply a bead of Silicone Sealant to Glass Panel
Inside and Outside as shown in 

Sketch 17 B. 

Clean the metal perimeter free from  dust and construction debree.

Inside Shower Stall 

Outside

SKETCH 17 A

Apply Silicone Sealant both ends

Summary of Contents for EPIC By-Pass Sliding Doors














Reviews:

No comments

Brands by name

Popular brands

Load more brands