Metal Fido/Trimline 35 & 50
Installation Instructions
PERMANENT WALL MOUNTING
Important Note
: Ensure that all relevant personnel read the points listed below and that a copy
is passed on to staff involved with the installation
®
TM
TM
YOU SHOULD HAVE
A - Bin Outer c/w Lid
B - M10 Washer x4
C - M10 Shake Washer x4
D - Hex-Head Screw x4
E - Top Bracket x1
F - Bottom Bracket x1
G - N
o
12 Wall Screws x 4
H - N
o
12 Plastic Wall Plugs x 4
J - M8 Washer x4
EQUIPMENT NEEDED
Installation Instructions
Electric/Cordless Power Drill
Masonry Drill Bit N
o
14 (9.32")
17mm Socket / Spanner
Screwdriver
Hammer
Marking Implement
Safety Glasses
1
After deciding where to site the bin and at what height, use the top
bracket (E) as a guide to mark the position of the two holes on the
wall. Ensure the two holes are horizontal and the correct distance
apart (as shown above in illustration).
2 Now mark the position of the two holes for the bottom bracket (F).
Do this by measuring 420 mm vertically down from each of the top
two holes.
3 When you are happy with the positioning of the holes, drill and
plug the wall, ready to accept brackets and screw fixings.
4 Using the wall screws (G) fix the top and bottom brackets onto the
wall.
5 Offer bin up to fixed wall brackets. Use washers (B & C) and
screws (D), to fix the bin to the brackets from the inside of the bin.
6 Ensure all of the fixing assembly is tightly secured.
Method
420
Metal Fido/Trimline 35 & 50
Installation Instructions
PERMANENT POST MOUNTING
Important Note
: Ensure that all relevant personnel read the points listed below and that a copy
is passed on to staff involved with the installation
®
TM
TM
YOU SHOULD HAVE
A - Bin Outer c/w Lid
B - M10 Washer x4
C - M10 Shake Washer x4
D - Hex-Head Screw x4
E - Top Bracket x1
F - Bottom Bracket x1
EQUIPMENT NEEDED
Installation Instructions
17mm Socket / Spanner
Screwdriver
1
UPPER MOUNTING
Hold the Top Bracket (E) to back of bin body, in line with the top
pair of pre-drilled holes. Using the Washers (B & C) and Hex-head
screws (D) fix the bracket assembly to the bin.
2
LOWER MOUNTING
Repeat the fixing operation with the Bottom Bracket (F).
Attach it to the bin through the lower pair of pre-drilled holes.
3 Fix around selected post using either TESPA banding or
TAMTORQUE system through both ‘C’ brackets.
NOTE: TESPA banding is not included with the kit, but is available
from Glasdon UK as a separate kit.
Method
Issue 2 August 2015
Stock no. C000/0370
DWG No. 07B-333-28
Copyright September 2010. Glasdon reserve the right to alter specification without prior notice.
A planned maintenance schedule of regular inspection is
recommended, replacing components as necessary.
Replacement components are available direct from GLASDON.
GLASDON cannot be held responsible for claims arising from
incorrect installation, unauthorised modifications or misuse of the
product.
C
, METAL FIDO
TM
AND METAL TRIMLINE
TM
ARE TRADEMARKS OR REGISTERED TRADEMARKS OF
GLASDON GROUP OR ITS SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES
®
®
Glasdon U.K. Limited
Preston New Road
BLACKPOOL
Lancashire
FY4 4UL
Tel: (01253) 600410
Fax: (01253) 792558
e-mail: [email protected]
web: www.glasdon.com
A
D
C
B
G
J
F
E
H
A
D
C
B
E
F