background image

Maintenance

11

Undermount-Installation

Installing the drain assembly

C

D

E

A

F

G

H

I

J

6

Install the strainer assembly (C-J) as these steps describe. It is 
easier to install the strainer assembly (C-J) to the sink (A) before 
the sink is installed to the cabinet.

Place the sink (A) into the installation hole to verify the fit. Adjust 
the cutout if necessary.

Apply a small amount of plumber’s putty (not included) in the notch 
around the drain hole of the sink (A). Place the strainer ring (E) on 
top of the drain hole in the sink (A).

1)

Put strainer basket (C) into the strainer bowl (D) and place this 
assembly into the drain hole in the sink (A).

2)

From underneath the sink (A), place the paper washer (F), rubber 
washer (G), locknut (H), plastic joint (I), and connecting nut (J) 
under the drain hole in the sink (A).

3)

Tighten the locknut (H) to hold the strainer assembly securely in 
place.

4)

Putting on the grid

7

Place the bottom grid (K) into the sink (A).

K

A

If you have a double bowl sink, install the assembly and put 
on the grid in the same way for the second bowl.

Summary of Contents for ACS3021A1Q














Reviews: