gk-medizinmechanik GK Magic 100 User Manual Download Page 9

 
Setting the temperature 

 
You  can  set  the  temperature  for  tub  fill  and  shower 
continuously.  To  do  that,  turn  the  knob  of  the  mixing 
valve  to  the  desired  position.  The  used  temperature 
will be shown in the display. 
 
 

Note: 

For  safety  reasons  the  temperature  is  mechanically 
limited  to  38  °C  (standard  mixer).  To  override  this 
security appliance, press the button on the knob. Thus 
it  is  possible  to  turn  the  knob  further  and  set  a 
higher temperature. 

 

Caution: 

When  setting  the  temperature  to  a  value  above  38  °C, 
set it back to 38 °C or lower as soon as possible! In 
the meantime, while the temperature is overridden, use 
extreme caution with the hot water. 

 
 

Temperature display tub fill & shower 

 
This display always shows the current tub fill respec-
tively shower temperature. 
 

Caution: 

Always check the water temperature with your bare hand 
(also when using the shower) before bringing the water 
in contact with the patient. 

 
 

Filling the tub 

 

Open the “TUB FILL VALVE” (in counter-clockwise direc-
tion)  to  fill  the  tub  with  water.  When  your  desired 
filling level is reached close the valve again to stop 
the water flow.

 

 
 
 

Filling the tub with control panel (if installed) 

 
If  the  knob  of  the  “TUB  FILL  VALVE”  is  not  present, 
then the tub can be filled by pressing the button “TUB 
FILL”.  Now  the  water  keeps  flowing  until  the  maximum 
filling  level  is  reached  or  the  button  is  pressed  a 
second time. If the water level is not high enough af-
ter  the  automatic  fill  stop,  you  can  press  and  hold 
the button “TUB FILL” for additional water flow. 
 

Note: 

If you want to use the door for  entering the bathtub, 
then  fill  the  bathtub  at  first  only  up  to  below  the 
doorstep. To do that when using the control panel, you 
must actively press the button at the right time. 

Functions 

Summary of Contents for GK Magic 100





















Reviews: