GIRBAU EH020 Operating Instructions Manual Download Page 45 | Manualshive

Page: 45 / 50

GIRBAU EH020 Operating Instructions Manual Download Page 45

Maintenance

45

Cod. 598144

Rev. 11/0717

14. MAINTENANCE

Caution



The users must refrain from carrying out actions reserved for the Authorised Technical
Services.



Before performing any work on the washing machine, disconnect and mechanically lock the
external switch, and close and mechanically lock the manual water inlet valves.



Check that the temperature of the parts to be handled represents no risk of burns.



The dispenser may contain residues of chemical products. In cleaning operations, avoid
direct contact with the skin and protect the eyes.



The draining pump and valve may contain residual water. When handling this component,
avoid direct contact with the skin and use eye protection.



Remember to reassemble ALL of the panels and replace them correctly after any
maintenance work.



It is highly recommended to ask the Authorised Technical Service for a register or report of
all the maintenance and service work done on your washer.

Operations described

USER-MAINTENANCE INSTRUCTIONS



Cleaning the washer (Section 14.1)



Cleaning the door seal (Section 14.2)



Cleaning the solenoid valve filters (section 14.3)



Checking safety devices (section 14.4)

ONLY TO BE PERFORMED BY THE AUTHORISED TECHNICAL SERVICE



Cleaning the dispenser (Section 14.5)



Cleaning the draining pump (models

HS-6008/EH020

) (section 14.6)



Checking the condition of the bearing housing seals (Section 14.7)



General overhaul (Section 14.8)

14.1. Cleaning the washer



We recommend cleaning the outside of the washing machine periodically. Use a damp cloth or sponge.



To remove grease marks use a neutral soap and rinse well.



Never use abrasive products or tools that could scratch or damage the surface of the washing machine.

14.2. Cleaning the door seal



Use a damp cloth or sponge.



Be especially careful to remove traces of laundry products or pieces of fabric that could be caught between

the folds of the seal.



Never use abrasive products or tools that could cut or damage the seal.

«
...
43
44
45
46
47
...
»

Summary of Contents for EH020



















































Reviews:

No comments