Girard Systems 98GC230 Installation Manual Download Page 4 | Manualshive

Page: 4 / 11

background image

Page 4 of 11

PRODUCT DESCRIPTION

The 98GC230 is a Dual channel RF transmitter, powered by two 3v Lithium batteries

(CR2032) designed to control a single awning by means of three push buttons for each

channel IN, STOP and OUT. As displayed in the picture below.

The faceplate can be removed easily by holding the module at the left and right edges

firmly in one hand and push the STOP button with two fingers of your other hand. The

picture below shows how the batteries must be inserted.

«
...
2
3
4
5
6
...
»

Summary of Contents for 98GC230












Reviews:

No comments

Related manuals for 98GC230

Brand: Barksdale Pages: 5

Brand: Zigen Pages: 40

Brand: Zigen Pages: 4

Brand: National Instruments Pages: 32

Draco major K474-U8/C8

Brand: Ihse Pages: 167

Brand: steute Pages: 10

Brand: LIVOLO Pages: 14

Brand: Clever Little Box Pages: 15

Brand: Tripp Lite Pages: 12

Brand: Wavetronix Pages: 3

Brand: PABX Pages: 46

S5560S-EI Series

Brand: H3C Pages: 47

Brand: WAGO Pages: 36

Brand: J-Tech Digital Pages: 13

Brand: ATEN Pages: 21

Brand: Gefen Pages: 9

Brand: Linksys Pages: 4

Brand: Alaxala Pages: 522

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands