Gira 0318 02 Installation Instructions Manual Download | Manualshive

Page: 15 / 15

background image

GIRA

Info

Radio-Control Presence Detector

Installation Instructions

Radio-Control Presence Detector

7/07

Page 15 of 15

N.B.

An adhesive label with the preset special light control
functions for radio-control transmitters (Fig. 12.)
‘Komfort’ is supplied with the detector.

12.)

Acceptance of guarantee

We accept the guarantee in accordance with the corresponding legal provisions.

Please return the unit postage paid to our central service department giving a brief description of the
fault:

Gira
Giersiepen GmbH & Co. KG

Service Center

Dahlienstrasse 12
D-42477 Radevormwald

Gira
Giersiepen GmbH & Co. KG
Postfach 1220
D-42461 Radevormwald

Telefon: +49 / 21 95 / 602 - 0
Telefax: +49 / 21 95 / 602 - 339
Internet: www.gira.de

«
...
13
14
15

Summary of Contents for 0318 02
















Reviews:

No comments

Related manuals for 0318 02

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 76

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 32

HomeHawk KX-HNC800

Brand: Panasonic Pages: 2

BL-C10A - Network Camera - Pan

Brand: Panasonic Pages: 4

Brand: La Crosse Technology Pages: 2

Brand: Takex Pages: 8

Brand: SAFE-T-ALERT Pages: 5

Brand: Basalte Pages: 2

Brand: Majorcom: Pages: 15

Brand: ZowieTek Pages: 24

WISENET XNO-8080R

Brand: Hanwha Techwin Pages: 13

Brand: Rosslare Pages: 34

Brand: Argo Pages: 7

Brand: ritm Pages: 22

Brand: Blaupunkt Pages: 61

Brand: Knauer Pages: 101

Brand: Speco Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands