background image

Gilson Aqua-Check Moisture Tester, MA-26X 

9

For help with operation or technical issues, 

Email: [email protected] or Call: 800.444.1508

5.0  TROUBLESHOOTING

 

Low 

High

  Readings 

Readings

  Possible Cause

Solution

GILSON AQUA-CHECK TROUBLESHOOTING

 

Testing procedure errors 

Review instructions and procedures.

 

Incorrect sample weights 

Check balance operation and re-zero.

 

Errors in corrected values 

Change in material type. Repeat correlation procedure with new material.

 

 

Insufficient agitation 

Some cohesive materials may require 3 minutes or more. Use Steel Pulverizing Balls.

 

 

Insufficient quantity of reagent 

Add an additional scoop of reagent.

 

 

Ineffective reagent 

Replace with fresh MAA-44 Reagent.

 

 

Premature contact between reagent 

Ensure vessel is held horizontal when mating with cap. 

 

 

 

and specimen 

 

 

Insufficient sample preparation 

Break cohesive material into finer sizes and use Pulverizing Balls.

 

 

Inadequate pressure seal 

Check and clean chamber cap gasket. Inspect Vessel, cap, and stirrup for damage  

 

 

 

 

or cracks. Replace gasket if necessary.

 

Defective gauge 

Gauge needle should rest at zero and move smoothly. Replace if defective.

 

 

Low temperature 

Run two or three test cycles to warm up Vessel.

 

 

High temperature 

Allow Vessel to cool off.

 

 

Moisture inside vessel prior to testing 

Insure Vessel and cap are completely dry before testing.

 

Gauge reading error 

Hold vessel horizontally at eye level when reading gauge.

 

 

Residue from previous tests 

Use included Coarse-Bristle Brush to clean vessel thoroughly between tests.

MAA-47

MAA-48

6.0 ACCESSORIES

Calcium Carbide Reagent, 10lb can¹ 

MAA-44

Aqua-Check 0–20% Pressure Gauge 

MAA-45

Electronic Balance, 220x0.1g 

OB-205

1.25in (32mm) Steel Balls, pkg. 2 

MAA-47

Long-Handle Reagent Scoop 

MAA-48

Large, Coarse-Bristle Brush 

MAA-51

Small, Fine-Bristle Brush 

MAA-50

Sample Cup 

MAA-52

Heavy-Duty Waterproof Plastic Case 

MAA-46

¹ Due to shipping restrictions, reagent is sold separately in 10lb (4.5kg) cans.  

Material from these larger cans can be used to replenish smaller containers for 

field use. 

GILSON AQUA-CHECK ACCESSORIES

Description

Model

Summary of Contents for Aqua-Check MA-26X










Reviews: