GILBARCO VEEDER-ROOT FlexPay IV Upgrade Instructions Download Page 22 | Manualshive

Page: 22 / 26

background image

MDE-5491A

18

SECTION 4 - INSTALLATION

4

Cables

To connect the cables:

1

Connect all cable connections from the electronics on the 10.4-inch display E-CIM door. The following
are the cable connections:

• M14346 video cable from UPM to PIP3

• M14340 Power Cable to PIP3, UPM, and card reader

• M14339 Serial Cable from PIP3

• M14338A001 and M14425A001 Applause Media System Cables (if present) from UPM and PIP3

• Speaker or intercom cable (if present) from PIP3

• USB cable from UPM to PIP3

• USB cable from printer

• Ethernet cables from UPM and card reader

• M13119 Cable from door node

Figure 2: Printer Cable Connection for Alphanumeric Door

Connect the 24 V power
cable from the printer to
the power supply board

Connect the USB cable
from the printer to PIP3

Connect the printer ground
cable to the U-Channel ensuring
to keep it separated from the
printer 24 V power cable

«
...
20
21
22
23
24
...
»

Summary of Contents for FlexPay IV



























Reviews:

No comments

Related manuals for FlexPay IV

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

Brand: MADRIX Pages: 12

Brand: Narcotrend Pages: 47

Brand: Uchida Yoko Pages: 40

Brand: Abus Pages: 12

Brand: Easylife Pages: 3

Brand: Phenix Technologies Pages: 39

Brand: Ganter Norm Pages: 20

Brand: Coba Pages: 2

Brand: HOMCOM Pages: 11

Brand: Veeder-Root Pages: 58

Brand: Kaya Safety Pages: 5

Brand: LandStal Pages: 19

Connex Vital Signs Monitor 6000 Series

Brand: Welch Allyn Pages: 143

Brand: SIGLENT Pages: 188

Brand: Sanity Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands