manualshive.com logo in svg

GigaDevice Semiconductor GD32F403 Series, User Manual

The GigaDevice Semiconductor GD32F403 Series offers a comprehensive user manual for easy navigation and optimal usage. Available for free download at manualshive.com, this manual provides detailed instructions, troubleshooting tips, and specifications to enhance your experience with these exceptional semiconductor devices.

Share
Download
background image

                                                                                                     

GD32F403xx User Manual

 

560 

 

These bits define the remaining number words to be written or read from the FIFO. 

It loads the data length register (SDIO_DATALEN[24:2]  if SDIO_DATALEN  is 

word-aligned or SDIO_DATALEN[24:2]+1  if SDIO_DATALEN  is not word -aligned) 

when DATAEN  is set, and start count decrement when a word write to or read 

from the FIFO. 

20.8.15. 

FIFO data register  (SDIO_FIFO) 

Address offset: 0x80 
Reset value: 0x0000 0000 

This register occupies 32 entries of 32-bit words, the address offset is from 0x80 to 0xFC. 

This register has to be accessed by word(32-bit) 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

FIFODT[31:16] 

rw 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

FIFODT[15:0] 

rw 

 

Bits 

Fields 

Descriptions 

31:0 

FIFODT[31:0] 

Receive FIFO data or transmit FIFO data 

These bits are the data of receive FIFO or transmit FIFO. Write to or read from this 

register is write data to FIFO or read data from FIFO.   

 

 

 

Summary of Contents for GD32F403 Series








































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F403 Series

ABB 650 series Engineering Manual preview
650 series
Brand: ABB Pages: 128
Camozzi PRE Series Operation And Maintenance Instructions preview
PRE Series
Brand: Camozzi Pages: 33
Camozzi PME Series Operation & Maintenance Instructions Manual preview
PME Series
Brand: Camozzi Pages: 64
Danfoss VLT AQUA Drive FC 202 Installation Manual preview
VLT AQUA Drive FC 202
Brand: Danfoss Pages: 124
Danfoss AME 55 Installation Manual preview
AME 55
Brand: Danfoss Pages: 2
Danfoss AME 110 NL Datasheet preview
AME 110 NL
Brand: Danfoss Pages: 8
Danfoss AK-CH 650 User Manual preview
AK-CH 650
Brand: Danfoss Pages: 114
Danfoss AME 438 SU Installation Manual preview
AME 438 SU
Brand: Danfoss Pages: 24
Danfoss ECL Comfort 296 Operating Manual preview
ECL Comfort 296
Brand: Danfoss Pages: 159
Danfoss VLT AutomationDrive FC 301 Operating Manual preview
VLT AutomationDrive FC 301
Brand: Danfoss Pages: 78
Danfoss AME 335 Installation Manual preview
AME 335
Brand: Danfoss Pages: 20
Danfoss CCR2 Installation Manual preview
CCR2
Brand: Danfoss Pages: 64
Harsco Industrial ENVI Advanced User'S Manual preview
ENVI
Brand: Harsco Industrial Pages: 57
Swagelok TBVS4 User Manual preview
TBVS4
Brand: Swagelok Pages: 16
ACTi R12CP-30 Installation Manual preview
R12CP-30
Brand: ACTi Pages: 20
SOARNEX EWC-100 Quick Installation Manual preview
EWC-100
Brand: SOARNEX Pages: 14
Viconics ZigBee Pro VT8000 Series Installation Manual preview
ZigBee Pro VT8000 Series
Brand: Viconics Pages: 3
MAKOT UMS-04 Series Manual preview
UMS-04 Series
Brand: MAKOT Pages: 6

Brands by name

Popular brands

Load more brands