Gigabyte R282-G30 User Manual Download Page 81

Page: 81 / 109

- 81 -

BIOS Setup

Parameter

Description

Memory RAS Configuration

(continued)

Leaky bucket time window based interface

– Enable/Disable leaky bucket time window based interface.

– Options available: Disabled, Enabled. Default setting is

Disabled

Leaky bucket low bit

–

Configures leaky bucket low bit (1-63).

– Press the <+> / <-> keys to increase or decrease the desired

values.

Leaky bucket high bit

–

Configures leaky bucket high bit (1-63).

– Press the <+> / <-> keys to increase or decrease the desired

values.

ADDDC Sparing

– Enable/Disable ADDDC Sparing.

– Options available: Disabled, Enabled. Default setting is

Disabled

Column Correction Disable

– Options available: Disable, Enable. Default setting is

Disable

Set PMem Die Sparing

– Options available: Disabled, Enabled. Default setting is

Disabled

Patrol Scrub

– Options available: Disabled, Enabled, Enable at End of POST.

Default setting is

Disabled

Summary of Contents for R282-G30














































































































Search results

Summary of Contents for R282-G30

Reviews:

Gigabyte R282-G30, User Manual, Page: 81 / 109

Search results

Summary of Contents for R282-G30

Reviews: