Gigabyte GR-ES604 Quick Installation Manual Download Page 15 | Manualshive

Page: 15 / 24

background image

15

4.5.

Install DVD and connect cable

Step 1.  Remove the front bezel.
Step 2.  Push inward to remove the dummy cover.
Step 3.  Slide the DVD-ROM drive into the bay until it locks into place.
Step 4.  Secure the DVD-ROM drive with screws to the chassis.
Step 5.  Connect the cable to the DVD-ROM drive.
Step 6.  Connect the power to the DVD-ROM drive.
Step 7.  Connect the cable to the motherboard connector.

Step 1

Step 2

Step 2

Step 2

Step 3

Step 4

Step 4

Step 5

«
...
13
14
15
16
17
...
»

Summary of Contents for GR-ES604

























Reviews:

No comments

Related manuals for GR-ES604

Brand: NEC Pages: 106

BladeCenter HS23

Brand: IBM Pages: 36

Brand: H3C Pages: 22

Brand: H3C Pages: 3

LS42 - BladeCenter - 7902

Brand: IBM Pages: 194

Brand: Patton electronics Pages: 51

Garage Gator GGR220

Brand: V-Bro Products Pages: 18

ControlPoint 2000

Brand: 4Home Pages: 20

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Brand: TRENDnet Pages: 62

Brand: Fastora Pages: 24

Brand: 7starlake Pages: 67

ValueLoader LTO-1

Brand: Quantum Pages: 76

FusionServer 5288 V6

Brand: xFusion Digital Technologies Pages: 131

Brand: MaxComm Pages: 10

Brand: Enterasys Pages: 62

HD-HCU2 DriveStation

Brand: Buffalo Pages: 8

Brand: Brocade Communications Systems Pages: 176

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands