Gigabyte GR-ES604 Quick Installation Manual Download Page 12 | Manualshive

Page: 12 / 24

background image

12

4.3.

Install HDD and connect cable

Step 1.  Inset a hard disk into hard disk blank.
Step 2.  Secure the hard disk wit h two screws.
Step 3.  Reverse the server system, lock another screw.
Step 4.  Connect the power cable to the hard disk. (See the arrow illustrated

below)

Step 5. Connect the power cable to the motherboard connector. Installation

completed.

Step 1

Step 2

Step 2

Step 3

Step 4

Step 5

«
...
10
11
12
13
14
...
»

Summary of Contents for GR-ES604

























Reviews:

No comments

Related manuals for GR-ES604

Brand: D-Link Pages: 12

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 16

XCubeNAS XN7012R

Brand: Qsan Pages: 16

Brand: QNAP Pages: 20

Brand: Draytek Pages: 8

SUPERSERVER 5018D-MHR7N4P

Brand: Supermicro Pages: 126

FusionServer CH242 V5

Brand: xFusion Digital Technologies Pages: 61

Brand: Perle Pages: 491

Brand: Razer Pages: 17

Brand: Topcom Pages: 16

Brand: SMC Networks Pages: 56

Brand: Ubiquiti Pages: 20

TE100S8P - Fast Ethernet Switch

Brand: TRENDnet Pages: 11

Brand: ADTRAN Pages: 4

Brand: Glyph Pages: 7

ZENWORKS PATCH MANAGEMENT 6.4 SP2 - SERVER

Brand: Novell Pages: 390

Brand: Linksys Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands