Gigabyte GA-880GMA-USB3 User Manual Download

Page: 25 / 100

- 25 -

Hardware Installation

•

Be sure to connect fan cables to the fan headers to prevent your CPU and system from over-

heating. Overheating may result in damage to the CPU or the system may hang.

•

These fan headers are not configuration jumper blocks. Do not place a jumper cap on the

headers.

3/4) CPU_FAN/SYS_FAN (Fan Headers)

The motherboard has a 4-pin CPU fan header (CPU_FAN), a 4-pin system fan header (SYS_FAN). Most

fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in

the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU fan

speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat dis-

sipation, it is recommended that a system fan be installed inside the chassis.

CPU_FAN:

SYS_FAN:

Pin No.

Definition

GND

+12V /Speed Control

Sense

Speed Control

Pin No.

Definition

GND

+12V /Speed Control

Sense

Reserve

CPU_FAN

DEBUG

PORT

G.QBOFM

SYS_FAN

DEBUG PO

G.QBOFM

5) SATA3_0/1/2/3/4/5 (SATA 6Gb/s Connectors, Controlled by AMD SB850 South Bridge)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standards. Each SATA connector supports a single SATA device. The AMD SB850 south bridge

supports RAID 0, RAID 1, RAID 5, RAID 10, and JBOD. Refer to Chapter 5, "Configuring SATA Hard

Drive(s)," for instructions on configuring a RAID array.

•

A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard

drives are to be used, the total number of hard drives must be an even number.

•

A RAID 5 configuration requires at least three hard drives. (The total number of hard drives

does not have to be an even number.)

•

A RAID 10 configuration requires four hard drives.

Please connect the L-shaped end of

the SATA cable to your SATA hard

drive.

Pin No.

Definition

GND

TXP

TXN

GND

RXN

RXP

GND

DEBUG

PORT

G.QBOFM

SATA3_4

SATA3_2

DEBUG

PORT

G.QBOFM

SATA3_0

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

SATA3_3

SATA3_1

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

SATA3_5

Summary of Contents for GA-880GMA-USB3





































































































Search results

Summary of Contents for GA-880GMA-USB3

Reviews:

Related manuals for GA-880GMA-USB3

Brands by name

Popular brands

Gigabyte GA-880GMA-USB3, User Manual

Search results

Summary of Contents for GA-880GMA-USB3

Reviews:

Related manuals for GA-880GMA-USB3

Brands by name

Popular brands