Gigabyte GA-870-UD3P User Manual Download

Page: 43 / 100

- 43 -

BIOS Setup

2-6 Integrated Peripherals

OnChip SATA Controller (AMD SB850 South Bridge)

Enables or disables the SATA controller integrated in the AMD SB850 chip. (Default: Enabled)

OnChip SATA Type (AMD SB850 South Bridge, SATA3_0~SATA3_3 connectors)

Configures the operating mode of the integrated SATA3_0~SATA3_3 controller.

Native IDE

Allows the SATA controller to operate in Native IDE mode. (Default)

Enable Native IDE mode if you wish to install operating systems that support Native

mode.

RAID

Enables RAID for the SATA controller.

AHCI

Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface

(AHCI) is an interface specification that allows the storage driver to enable advanced

Serial ATA features such as Native Command Queuing and hot plug.

OnChip SATA Port4/5 Type (AMD SB850 South Bridge, SATA3_4~SATA3_5 connectors)

This option is configurable only when

OnChip SATA Type

is set to

RAID

AHCI

. Configures the oper-

ating mode of the integrated SATA3_4/SATA3_5 connectors.

IDE

Disables RAID for the SATA controller and configures the SATA controller to PATA

mode. (Default)

As SATA Type The mode depends on the

OnChip SATA Type

settings.

OnChip SATA RAID5 Support (AMD SB850 South Bridge, SATA3_0~SATA3_5 connectors)

Enables or disables RAID 5 support for the SATA controller integrated in the AMD SB850 South Bridge.

This option is configurable only when

OnChip SATA Type

is set to

RAID

OnChip SATA3.0 Support

Enables or disables the SATA 6Gb/s function integrated in the Chipset. When set to

Disabled

, the SATA

controller will operate in SATA 3Gb/s mode. (Default: Enabled)

Integrated Peripherals

OnChip SATA Controller

[Enabled]

OnChip SATA Type

[Native IDE]

x OnChip SATA Port4/5 Type

IDE

x OnChip SATA RAID5 Support

Enabled

OnChip SATA3.0 Suuport

[Enabled]

x OnChip SATA Port as ESP

Press Enter

Onboard LAN Function

[Enabled]

Onboard LAN Boot ROM

[Disabled]



SMART LAN

[Press Enter]

Onboard Audio Function

[Enabled]

USB Controllers

[Enabled]

USB Legacy Function

[Enabled]

USB Storage Function

[Enabled]

Onboard Serial Port 1

[3F8/IRQ4]

higf

: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

F5: Previous Values

F6: Fail-Safe Defaults

F7: Optimized Defaults

Item Help

Menu Level



Summary of Contents for GA-870-UD3P





































































































Search results

Summary of Contents for GA-870-UD3P

Reviews:

Related manuals for GA-870-UD3P

Brands by name

Popular brands

Gigabyte GA-870-UD3P, User Manual

Search results

Summary of Contents for GA-870-UD3P

Reviews:

Related manuals for GA-870-UD3P

Brands by name

Popular brands