Gigabyte GA-870-UD3P User Manual Download

Page: 47 / 100

- 47 -

BIOS Setup

ACPI Suspend Type

Specifies the ACPI sleep state when the system enters suspend.

S1(POS)

Enables the system to enter the ACPI S1 (Power on Suspend) sleep state.

In S1 sleep state, the system appears suspended and stays in a low power mode.

The system can be resumed at any time.

S3(STR)

Enables the system to enter the ACPI S3 (Suspend to RAM) sleep state (default).

In S3 sleep state, the system appears to be off and consumes less power than in

the S1 state. When signaled by a wake-up device or event, the system resumes to

its working state exactly where it was left off.

Soft-Off by Power button

Configures the way to turn off the computer in MS-DOS mode using the power button.

Instant-Off

Press the power button and then the system will be turned off instantly. (Default)

Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power

button is pressed for less than 4 seconds, the system will enter suspend mode.

USB Wake Up from S3

Allows the system to be awakened from ACPI S3 sleep state by a wake-up signal from the installed USB
device. (Default: Enabled)

Modem Ring Resume

Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a modem that
supports wake-up function. (Default: Disabled)

PME Event Wake Up

Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a PCI or PCIe de-
vice. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.
(Default: Enabled)

(Note) Supported on Windows 7/Vista operating system only.

2-7 Power Management Setup

Power Management Setup

ACPI Suspend Type

[S3(STR)]

Soft-Off by Power button

[Instant-off]

USB Wake Up from S3

[Enabled]

Modem Ring Resume

[Disabled]

PME Event Wake Up

[Enabled]

HPET Support

(Note)

[Enabled]

Power On By Mouse

[Disabled]

Power On By Keyboard

[Disabled]

x KB Power ON Password

Enter

AC Back Function

[Soft-Off]

Power-On by Alarm

[Disabled]

x Date (of Month)

Everyday

x Resume Time (hh:mm:ss)

0 : 0 : 0

ErP Support

[Disabled]

higf

: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

F5: Previous Values

F6: Fail-Safe Defaults

F7: Optimized Defaults

Item Help

Menu Level



Summary of Contents for GA-870-UD3P





































































































Search results

Summary of Contents for GA-870-UD3P

Reviews:

Related manuals for GA-870-UD3P

Brands by name

Popular brands

Gigabyte GA-870-UD3P, User Manual

Search results

Summary of Contents for GA-870-UD3P

Reviews:

Related manuals for GA-870-UD3P

Brands by name

Popular brands