Gigabyte E152-ZE1 User Manual Download Page 90

Page: 90 / 136

BIOS Setup

- 92 -

5-3-3-1-1

DRAM Controller Configuration

Parameter

Description

DRAM Controller Configuration

DRAM Power Options

Press [Enter] to configure DRAM Power OptionsMa.

Power Down Enable

– Enable/Disable DDR power down mode.

– Options available: Auto, Enabled, Disabled. Default setting is

Auto

Power Down Entry Delay

SubUrgRefLowerBound

UrgRefLimit

DRAM Maximum Activate Count

– Options available: Auto, Unlimited MC, 200K,300K, 400K, 500K,

600K, 700K. Default setting is

Auto

DRAM Refresh Rate

– Options available: 7.8 usec, 3.9 usec. Default setting is

7.8 usec

Self-Refresh Exit Staggering

– Options available:Disabled, Trfc/3, Trfc/4. Default setting is

Disabled

Cmd2T

Selects the Cmd2T mode on ADDR/CMD.
Options available: Auto, 1T, 2T. Default setting is

Auto

Gear Down Mode

Enable/Disable the Gear Down Mode function.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

Summary of Contents for E152-ZE1









































































































































Search results

Summary of Contents for E152-ZE1

Reviews:

Brands by name

Popular brands

Gigabyte E152-ZE1, User Manual

Search results

Summary of Contents for E152-ZE1

Reviews:

Brands by name

Popular brands