Gigabyte E152-ZE1 User Manual Download

Page: 56 / 136

BIOS Setup

- 58 -

5-2-6 Serial Port Console Redirection

(Note) Advanced items prompt when this item is defined.

Parameter

Description

COM1 Serial Over LAN

(Note))

Select whether to enable console redirection for specified device. Console

redirection enables the users to manage the system from a remote
location.
Options available: Enabled/Disabled. Default setting is

Disabled

COM1 Serial Over LAN
Console Redirection Settings

Press [Enter] to configure advanced items.

Please note that this item is configurable when COM1/Serial Over

LAN & COM2 Console Redirection is set to Enabled.

Terminal Type

– Selects a terminal type to be used for console redirection.

– Options available: VT100, VT100+, ANSI, VT-UTF8. Default setting

ANSI

Bits per second

– Selects the transfer rate for console redirection.

– Options available: 9600, 19200, 38400, 57600, 115200. Default

setting is

115200

Data Bits

– Selects the number of data bits used for console redirection.

– Options available: 7/8. Default setting is

Summary of Contents for E152-ZE1









































































































































Search results

Summary of Contents for E152-ZE1

Reviews:

Related manuals for E152-ZE1

Brands by name

Popular brands

Gigabyte E152-ZE1, User Manual

Search results

Summary of Contents for E152-ZE1

Reviews:

Related manuals for E152-ZE1

Brands by name

Popular brands