manualshive.com logo in svg

Gigabyte E152-ZE1, User Manual

Share
Download
Gigabyte E152-ZE1 User Manual Download Page 89

- 91 -

BIOS Setup

5-3-3-1 DDR4 Common Options

Parameter

Description

DDR4 Common Options

Enforce POR

Press [Enter] to configure the Plan of Record (POR) to enable / disable 

restrictions for DDR4 frequency and voltage programming. Memory speeds 
will be capped at AMD guidelines.

Note: To enable 2 DIMMs per Channel at 3200MHz function, select 
[Accept] at warning message, change Overclock from [Auto] to 
[Enabled], and then set memory speed to 3200MHz.

DRAM Controller Configuration Press [Enter] to configure DRAM Controller Configuration.
CAD Bus Configuration

Press [Enter] to configure CAD Bus Configuration.

Data Bus Configuration

Press [Enter] to configure Data Bus Configuration.

Common RAS

Press [Enter] to configure Common RAS.

Security

Press [Enter] to configure Security.

Phy Configuration

Press [Enter] to configure Security.

Summary of Contents for E152-ZE1









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands