Gigabyte AirCruiser GN-BR32L-RH User Manual Download Page 20

Page: 20 / 90

GN-BR32L-RH 2.4GHz AirCruiser Ultra N Wireless Router

is 192.168.1.254

LAN Netmask 1

Displays the IP Subnet Mask being used by the

Local (LAN) port of the router. Default is
255.255.255.0

LAN IP 2 Address

Displays the alternate IP address being used by
the Local (LAN) port of the Router

LAN Netmask 2

Displays the alternate IP Subnet Mask being used
by the alternate Local (LAN) port of the router.

LAN DHCP Status

Identifies if the Router’s built-in DHCP server is
active for the LAN attached devices.

LAN DHCP Start IP

The starting IP number in the range possible IP
addresses issued by the DHCP server

LAN DHCP End IP

The last IP number in the range possible IP
addresses issued by the DHCP server

The LAN Ethernet Status Tab

On the LAN Ethernet Status the Router displays the Ethernet Status of
the current LAN current connection.

MAC

This field displays the MAC

address of the portable AP as seen
on your wireless network.

MTU

This specifies the maximum

size of the packet permitted for
Internet transmission.

Rx packets

The number of data

packets received by the AP.

Tx packets

The number of data

packets transmitted by the AP.

Rx bytes

The current bandwidth

(receive) on the LAN port.

x bytes

The current bandwidth

(transmit

)

on the LAN port.

The WAN Ethernet Status button

MAC

The field displays the MAC

address used by the WAN port of the
AP.

Summary of Contents for AirCruiser GN-BR32L-RH



























































































Search results

Summary of Contents for AirCruiser GN-BR32L-RH

Reviews:

Related manuals for AirCruiser GN-BR32L-RH

Brands by name

Popular brands

Gigabyte AirCruiser GN-BR32L-RH, User Manual

Search results

Summary of Contents for AirCruiser GN-BR32L-RH

Reviews:

Related manuals for AirCruiser GN-BR32L-RH

Brands by name

Popular brands