Gigabyte AirCruiser GN-BR32L-RH User Manual Download Page 11

Page: 11 / 90

GN-BR32L-RH 2.4GHz AirCruiser Ultra N Wireless Router



DHCP server for Wireless and LAN connections



Conforms to IEEE 802.11n specification.



Wireless transmits data rate up to 150 and receives to 150Mbps.



64-bit /128-bit WEP encryption, 802.1x, WPA and WPA2.



Wi-Fi Protected Setup



Wireless Bridge WDS



Smart Setup for auto configuration



PPPoE DSL connection



DHCP client for cable/DSL connection



UPnP IGD 1.0



MSN messenger and most Internet applications



Firewall

Filtering



Virtual

Server



DMZ



Stateful Packet Inspection



DoS

Protection



Stealth

Mode



VPN Packets Pass Through (PPTP/IPSec/L2TP Protocol)



Log Management (Support Firewall/UPnP/WAN Connection Log)



WAN side Remote Management



URL

Blocking



DNS Relay and Dynamic DNS



QoS WMM, WMM Power Save



EZ Hot Spot supports dual SSIDs (One SSID enhance traffic
control feature)



WAN bandwidth management

Summary of Contents for AirCruiser GN-BR32L-RH



























































































Search results

Summary of Contents for AirCruiser GN-BR32L-RH

Reviews:

Related manuals for AirCruiser GN-BR32L-RH

Brands by name

Popular brands

Gigabyte AirCruiser GN-BR32L-RH, User Manual

Search results

Summary of Contents for AirCruiser GN-BR32L-RH

Reviews:

Related manuals for AirCruiser GN-BR32L-RH

Brands by name

Popular brands