manualshive.com logo in svg

Gigabyte AirCruiser GN-BR30N-RH, User Manual, Page: 9 / 85

Share
Download
Gigabyte AirCruiser GN-BR30N-RH User Manual Download Page 9

GN-BR30N-RH 2.4GHz AirCruiser N300 Wireless Router

 

3 

LEDs 

 

 

 

Figure 2: LED Layout 

 

 

The table below describes the LED indicators on the front 
panel of the GN-BR30N-RH.    All LEDs are green when lit. 

 

 

 

LED 

STATUS 

DESCRIPTION 

Green 

Power is supplied to the Router 

Power 

Off 

Power is NOT supplied to the Router 

WLAN 

Flashing 

Data is being transmitted wirelessly 

On 

WAN port has detected a wired link with a 
DSL or Cable modem. 

WAN 

Flashing 

Data is being transmitted / received 
through WAN port. 

On 

LAN port has detected a link with a 
10/100Mbps device 

LAN 

Flashing 

Data is being transmitted / received 
through LAN port. 

 

Key Features 

¾

 

Support Smart Setup for auto configuration 

¾

 

Conforms to IEEE 802.11n specification. 

¾

 

Wireless transmits data rate up to 300Mbps. 

¾

 

Support 64-bit /128-bit WEP encryption, 802.1x, WPA™ and WPA™2. 

¾

 

Support PPPoE and PPPoE Unnumbered DSL connection 

Power LED

 

WLAN LED

 

LAN LED 

(4) 

WAN LED

 

Summary of Contents for AirCruiser GN-BR30N-RH






















































































Reviews:

No comments