background image

GIANT INDUSTRIES, INC.

 

900 N. Westwood Ave.,            

Toledo, Ohio  43607

PHONE (419) 531-4600

 FAX (419) 531-6836 

www.giantpumps.com

©  Copyright 2018 Giant Industries, Inc.

 

 

 

 

 

 

 

01/18   P435/455B.indd

GIANT INDUSTRIES LIMITED WARRANTY

Giant Industries, Inc. pumps and accessories are warranted by the manufacturer to be free 

from defects in workmanship and material as follows:

 

1. 

For portable pressure washers and self-service car wash applications, the 

discharge manifolds are guaranteed for the life of the pump. Our other pump 

parts, used in portable pressure washers and in car wash applications, are 

warranted for five years from the date of shipment for all pumps used in 

NON-SALINE, clean water  applications.

 

2.   

One (1) year from the date of shipment for all other Giant industrial and    

  consumer 

pumps.

 

3.   

Six (6) months from the date of shipment for all rebuilt pumps.

 

4.   

Ninety (90) days from the date of shipment for all Giant accessories.

                   

This warranty is limited to repair or replacement of pumps and accessories of which the  

manufacturer’s evaluation shows were defective at the time of shipment by the manufacturer.  

The following items are NOT covered or will void the warranty:

 

1.  

Defects caused by negligence or fault of the buyer or third party.

 

2.   

Normal wear and tear to standard wear parts.

 

3.  

Use of repair parts other than those manufactured or authorized by Giant.

 

4.  

Improper use of the product as a component part.

 

5.  

Changes or modifications made by the customer or third party.

 

6.  

The operation of pumps and or accessories exceeding the specifications set  

 

 

forth in the Operations Manuals provided by Giant Industries, Inc.

Liability under this warranty is on all non-wear parts and limited to the replacement or repair 

of those products returned freight prepaid to Giant Industries which are deemed to be defec-

tive due to workmanship or failure of material.  A Returned Goods Authorization (R.G.A.) 

number and completed warranty evaluation form is required prior to the return to Giant In-

dustries of all products under warranty consideration.  Call (419)-531-4600 or fax (419)-531-

6836 to obtain an R.G.A. number.

Repair or replacement of defective products as provided is the sole and exclusive remedy 

provided hereunder and the MANUFACTURER SHALL NOT BE LIABLE FOR FURTHER 

LOSS, DAMAGES, OR EXPENSES, INCLUDING INCIDENTAL AND CONSEQUENTIAL 

DAMAGES DIRECTLY OR INDIRECTLY ARISING FROM THE SALE OR USE OF THIS 

PRODUCT.

THE LIMITED WARRANTY SET FORTH HEREIN IS IN LIEU OF ALL OTHER WARRAN

-

TIES OR REPRESENTATION, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITA

-

TION ANY WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR 

PURPOSE AND ALL SUCH WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED 

BY THE MANUFACTURER.

  

Summary of Contents for P435













Reviews: