manualshive.com logo in svg

Giant-Vac 3800014, Manual, Page: 19 / 24

Share
Download
Giant-Vac 3800014 Manual Download Page 19

Giant-Vac Model TL652951W Truck Loader 

 

SHEET 4  - TRAILER GROUP (CHW version only) 

 

 

 

 

REF # 

PART # 

DESCRIPTION 

QTY 

 

 

 

 

1 

----- 

Loader base and trailer frame (see engine group) 

--- 

2 

38004 Draw 

bar 

1 

3 

31084 

Bolt, hex - 1/2-13 x 1-1/4” 

4 

4 

31078 

Washer, lock - 1/2 

4 

5 

31406 

Nut, reverse lock - 1/2-13 

4 

6 

31821 

Bolt, hex - 1/2-13 x 7” 

1 

7 

31043 

Washer, flat - 1/2 

4 

8 

31641 

Chain, safety towing 

2 

9 

31406 

Nut, lock - 1/2-13 

1 

10 

33173 

Jack, dual wheel support 

1 

11 

31033 

Bolt, hex - 3/8-16 x 1" 

4 

12 

31008 

Washer, lock - 3/8 

4 

13 

31009 

Nut, lock - 3/8-16 

4 

14 

33297 Axle, 

Torflex 

1 

15 

32154 

Bolt, hex, black oxide, 1/2-13 x 1-1/4 gr 5 

4 

15a 

32155 

Washer, flat, 1/2” 

8 

16 

31078 

Washer, lock - 1/2" 

4 

17 

32156 

Nut, hex end lock – 1/2-13 

4 

18 

33051 

Tire and wheel assy 

2 

19 

31148 Lug 

nut 

10 

20 

40105 Leg, 

support 

1 

21 

31125 

Pin, clevis - 3/8 x 4-1/2" 

1 

22 

31126 Pin, 

bridge 

1 

23 

31639 

Light, tail/stop assy 

2 

24 

31831 Harness, 

wiring 

1 

--- 

31644 

Clip, wiring harness, slip-on – large  

10 

--- 

32012 

Clip, wiring harness, bolt-on – 3/8” nom 

2 

--- 

31562 

Screw, self-tapping - #12 x 3/4 (secures bolt-on clips to frame) 

2 

25 

32090 

Screw, self-tapping - #10 x 1/2 (taillight ground) 

2 

26 

31752 Bracket, 

license 

1 

27 

31751 Light, 

license 

1 

28 

31444 

Bolt, hex - 1/4-20 x 1 – bolts license light assy to frame 

2 

--- 

31013 

Washer, lock - 1/4" 

2 

--- 

31030 

Nut, hex - 1/4-20 

2 

29 

31125 

Pin, clevis - 3/8 x 4-1/2" 

1 

30 

31126 Pin, 

bridge 

1 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Manual No. 3100022 

 

Not 

for  

Reproduction

Summary of Contents for 3800014

























Reviews:

No comments