Giant-Vac 10BA Assembly Instructions Operator'S Manual Parts List Download Page 2

 

 

 

 

1

 

preliminaries 

 

Congratulations! 

 

You have just purchased one of the finest pieces of outdoor power equipment on the market today.  If properly 
cared for, your new blower will provide years of dependable service.  Please read and follow this instruction 
manual carefully in order to get the most out of your new equipment. 
 
As you carefully unpack your unit, you will find the following items: 

 

      1  Blower Unit 

1 Handle 

Assembly 

including: 

1 – Upper Handle with foam grip 
2 – Lower Handles 
1 – Handle Support Panel 

1   Front Caster Wheel Kit

 including: 

1 – Front Caster Bracket 
3 – Mounting Bolts with lock washers and flat washers 
1 – Front Caster Wheel 
1 – Axle Bolt with lock nut 

1  Package of assembly hardware 
1  Package containing operating manuals and warranty registration 

 

Each product leaves our factory in excellent condition; occasionally, however, some damage may occur during 
shipment.  If any such damage is found upon initial inspection, 

immediately

 notify the transport carrier who 

delivered your machine, as they are solely responsible for such damage, as well as any subsequent 
adjustments necessary.  
 

Before assembly, please take a moment and record your model number and serial number below for 
future reference (both numbers are located on the silver tag adhered to the rear of the unit, below and to 
the right of the engine): 
 

Model number_______________________________ 
 
Serial number________________________________ 

 

Also be sure to promptly fill out and return the warranty registration enclosed in your manual packet. 

 
Your new blower requires very little assembly.  Simply follow the instructions contained within this manual to 
begin enjoying the benefits of your new unit. 

 

 

CALIFORNIA PROPOSITION 65 WARNING

 

 

Gasoline and Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and 
other reproductive harm. 
 
As an owner of off-road gasoline or diesel engine equipment and/or as an employer, you also may have an obligation under the 
California Occupational Safety and Health Act or under Proposition 65 to warn persons exposed to gas and diesel engine exhaust 
and/or other Proposition 65 chemicals in and around your workplace.  See California Health and Safety Code section 25249.5, Title 22 of 
the California Code of Regulations at Section 1200 

er seq.,

 and Title 8 of the California Code of Regulations Section 5194. 

R0603.1 

Summary of Contents for 10BA

















Reviews: