background image

24

GENERAL

The manufacturer warrants that, subject to verification of a warranty 

claim within the warranty period as described below, it will take the 

necessary corrective action to either repair or replace a water heater 

or component part which is determined to be defective in material 

or workmanship subject to the terms and conditions outlined in this 

document. Further, any replacement water heater or component part 

supplied under warranty will carry only the unexpired portion of the 

original water heater’s warranty. The number of replacement water 

heaters is limited to one (1) per original unit purchased. If due to 

some extremely unusual circumstance, a replacement water heater 

or component part is found by our inspection & testing department 

to be defective, another heater or component part will be supplied to 

fulfill the obligation of the warranty of the original heater.

THE INNER TANK

If the inner tank fails within SIX (6) years after the date of the original 

installation, a replacement water heater will be provided to the party 

from whom the unit was originally purchased. If the water heater is 

installed in other than a single family dwelling, the tank warranty is 

limited to ONE (1) year. If an exact replacement is not available, 

the manufacturer reserves the right to furnish a comparable model 

water heater; however, a surcharge will be applied for any addi

-

tional component(s) incorporated in the replacement water heater. 

The 

warranty 

reply card 

must 

be completed 

and 

sent back 

to the 

manufacturer 

within 

forty-five 

(45) 

days 

of 

the 

installation 

date. 

If 

said warranty card is not returned, the date indicated on the model 

serial plate will prevail. 

COMPONENT PARTS

If 

any 

component 

part 

is 

found 

to 

be 

defective 

within 

ONE 

(1) 

year 

from the date of original installation, provided said defective part is 

an in-house factory made piece or an original factory approved OEM 

piece, the manufacturer will furnish a replacement part after the 

receipt and testing of the part claimed to be defective. 

THIS WARRANTY WILL NOT APPLY

1)

 

To defects or malfunctions resulting from failure to properly 

install, 

operate, 

or 

maintain 

the 

unit 

in 

accordance 

with 

the 

print

-

ed instructions.

2)

 

If 

the 

installation 

does 

not 

conform 

to 

CSA 

&/or 

ETL 

Standards 

as well as any applicable national or local building codes.

3)

 

To any damage or failure caused by abuse, accident, fire, floods, 

freezing, or other acts of God.

4)

 

To 

any 

damage 

or 

failure 

caused 

by 

operating 

the 

heater 

without 

an approved 

pressure & temperature relief valve 

having been 

installed.

5)

 

To any damage or failure caused by operating the heater with an 

empty or partially empty inner tank or sediment build-up result

-

ing in dry firing of the heating elements.

6)

 

To any damage or failure caused by utilizing the heater in con

-

junction with any other energy saving device or other source(s) 

of 

energy 

not 

approved 

by 

the 

manufacturer; 

or 

for 

other 

than 

use with potable water without any additives such as salt, chlo

-

rine, or chemicals other than those added for the purpose of 

rendering the water fit to drink.

7)

 

To any damage or failure caused by the removal of the anode 

&/or by not assuring that there is a working anode in the tank at 

all times. All anodes must be checked at least once every two 

years & replaced if necessary

8)

 

To any damages or failure caused by having affixed to the 

heater any non-factory made or factory approved replacement 

part(s) such as elements, controls, dip-tubes, relief valves, etc...

9)

 

To 

any 

damage 

caused 

by 

not 

having 

the 

water 

heater 

installed 

adjacent to a free flowing drain in the event of water leakage. 

10)

 If 

the heater is 

operated 

at 

water 

temperatures 

exceeding 

the 

maximum setting of the operating &/or high limit control or the 

heater is not supplied with potable water, free to circulate at all 

times.

11)

 If the heater has experienced the effect of thermal expansion 

due to excessive pressure (exceeding 300PSI). The result of 

excessive pressure usually reverses the bottom of the inner tank 

and can occur with the addition of a pressure reducing valve &/

or a check valve in the municipal water supply system in a single 

family dwelling.

12)

 If the heater is installed outside of Canada or the United States.

SERVICE LABOUR RESPONSIBILITY

This warranty does not cover any labour expense for service, remov

-

al, or re-installation of a replacement heater. All such expenses are 

your responsibility.

SHIPPING COSTS

If a water heater or component part is deemed to be replaced, the 

manufacturer will pay the transportation costs of the replacement 

unit to a convenient authorized distributor or retailer as selected by 

us. You must pay any local cartage including the cost of returning 

the replaced item to the authorized distributor or retailer from whom 

the replacement is coming from.

HOW TO MAKE A CLAIM

Any claim for warranty service should be made to your contractor, 

wholesaler, or retailer from whom the water heater was purchased. 

In turn, said contractor, wholesaler, or retailer will contact the manu

-

facturer from whom they purchased the heater. If this procedure 

cannot be followed, contact any other local contractor, wholesaler, 

or retailer handling our water heaters. Also, for warranty information 

you may call the manufacturer’s customer service department at 

(514) 

645-8893 

or 

1-800-363-9354, 

option 

1. 

We 

suggest 

that 

prior 

to 

calling the 

factory, 

that 

you 

make 

sure 

to 

have 

the 

model 

number 

& serial number that is to be found on the outside casing of the 

heater. Proof of purchase showing the date, name, and place of the 

business from whom the water heater was purchased is essential 

to settle any warranty claim dispute over the length of the period 

of installation.

If an exact replacement is not available, a current model water 

heater or component part with comparable operating features will be 

provided by the manufacturer. If government regulations or industry 

standards require the replacement model water heater or compo

-

nent part to have features not found on the defective model water 

heater or component part, you will be charged the difference in price 

associated with these required features. If you pay the difference in 

price for these required features, you will receive a complete new 

Standard Basic Limited Warranty for the replacement water heater.

MISCELLANEOUS

No 

one is 

authorized 

to make 

any other warranties on 

the manu

-

facturer’s 

behalf. Any 

implied 

warranties 

of 

any 

nature 

offered 

by 

third 

party other 

than 

what 

is 

stated 

in 

this 

Standard 

Basic 

Limited Warranty will not be honoured. No claims for incidental or 

consequential damages (including damages from leakage) will be 

accepted. 

 If 

you do not 

return the 

warranty 

card, 

a proof 

of 

pur

-

chase showing the name, date, and location of the original source 

of purchase is a necessity to process a warranty claim. Failure to 

produce this documentation will result in the lesser or the warranty 

periods being offered. In order to avoid any confusion &/or disputes, 

we suggest that the warranty card be completed and mailed back no 

later than forty-five (45) days after installation.

EXTENDED WARRANTIES

For information on some premium quality residential gas & electric 

water heaters, contact your local licensed plumber, or look for them 

at selected retailers.

STANDARD BASIC LIMITED WARRANTY

ON RESIDENTIAL GAS WATER HEATERS

Summary of Contents for UG50-59

























Reviews: